Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I am able to load the project.. I have followed all the instructions from nrf connect helkp and have verified it.
tag v1.1.0 (have done west update)
using SES 4.30c as...
I started with the Nrf_tempelate project and used nrf_uart_app to add uart service in it. The application works fine after reset and as long as it is connected to nrf connect...
Hi,
Given the too many examples in the nRF5 SDK that are provided to implement BLE and the unclear documentation on how to best proceed, what would you say is the quickest...
Hey..
I'm having difficulties using P1 pins for UART.
I just changed the blinky example for checking the P1 pin changes with it. But no changes where monitored as expected...
Hello, I'm a beginner in developing nRF52832. Using Keil version 5.29 on windows 10 (x64), I followed the steps described in getting started for nRF52 . However, I found 2...
Hi there,
I was wondering if Nordic(or anyone else) have an example available to handle various network issues a device could face in the field. For example during initial...
Hi. ... Everyone. .. I want to advertise my ADC .I am using nRF52832 ,15.2version sdk . I have seen my queries related to this topic,even I tried .but data is not advertising...
Hi,
I am using nRF52840DK along with S112 sdk15.3.0 as a peripheral device, i included timer and sleep function in ble_app_beacon example code . I am getting fatal error...
Hi,
I am currently working on a project to transfer data from a computer to an embedded device. During the implementation, I encountered problems to achieve the required...
Hello,
I am trying to run the asset tracker example on an nRF9160-DK and I get the following errors from the LTE Link Monitor:
2020-02-06T21:00:59.964Z DEBUG modem <<...
Hello all,
I use a 1NCE Sim and be based in Berlin Germany.
On the AT_Client example the LTE works very well but then I load the 'Asset Tracker' application on the...
Hi team,
I am using nRF52840 ,SDK 16.0.0 with s140 v7.0 .
I am not using any advertising module from nordic to advertise the packet .
In my own code, I suppose set the...
To the kind attention of Nordic support team,
I downloaded a fresh copy of sdk16. I putted to the test keil projects with secured gazell libraries. Now I'm only trying to...
I could use some clarity on the legacy drivers/files, nrf,driving example applications inside SDK 16. Is it just too much work to clean up the examples with current drivers...
