Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
Dear,
I am trying to test BLE on the nRF91 DK, I found an example: \nrf\samples\nrf9160\lte_ble_gateway
I tried with the master branch , but I got the error:
Then...
Hi,
I received my nRF9160 development board a week ago and tried to program it using the following guide:
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts...
Hello Everyone,
I'm currently developing a SoC and I would like to achieve a correct interaction between the SoC and the Nordic Nrf52832.
The output of the SoC is...
After a DFU, when the new firmware is booted a service changed indication is not being sent so iOS only sees the DFU service. Should the softdevice be sending the service...
Hi
We can't connect jlink to nRF52840,then we check the voltage of DEC pins, Is this correct?
And what's the function of DEC pins(DEC1\DEC2\DEC5)? The datasheet description...
Hi all
I have an identical problem to this: https://devzone.nordicsemi.com/f/nordic-q-a/51567/can-t-build-nrf-connect-project
All my setup is the same, and the problem...
I am trying to send multiple 64byte packets - in a loop - using app_usbd_hid_generic_in_report_set(). This together with the user event handler happens inside the same FreeRTOS...
NRF connect 2.1.0
OS: Ububtu 16.04
when I try to download linkmonitor I fet:
Unable to install: Unable to download registry.yarnpkg.com/pc-nrfconnect-linkmonitor . Got...
Hi all
Have been using the nRF52810 for a while now in production with no issues. We are developing a companion product that uses the nRF52811 and we cannot get the custom...
Hi I am using nrf51 SDK (version 10)
firmware:s110_nrf51_8.0.0_softdevice.
while uploading program in nrf51822 through J-segger I have getting following errors:
*...
Hi, nordic engineer:
Our project has a function, that is, BLE+Thread coexists. We hope that the mobile phone can upgrade the device through BLE. Can this idea be realized...
Hi everyone,
I am using nrf52832 with SDK version 11.0 for an IoT application. I am communicating with Atmel ATWINC 1500 module through SPI in order to connect to Wifi...
Hi,
I have a custom implemented DFU that I used in many nRF52832 designs.
This one in particular fails when I am calling nrf_fstorage_erase. I am trying to erase 40...
