I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
I have been trying to use the new GPS example, however, I could not get any location from it yet. It seems that after 30 tries, it stops working (time-out problem). Should...
Hi all,
I'm starting developping code with SES, on an nRF52810 (192kB of Flash), with the BLE stack S112.
Because my project include BLE and custom UUID, I started with...
Hi
I am using the nrf53832 dk.
In the nus example once the data is received from the phone(central) I want to write this data to the flash. I referred to the fstorage...
Hi everyone,
We are currently working on a BLE border router with a module based on nrf52840. The custom board has a MAC + PHY ethernet controller that communicates with...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have gone through below...
Hi everyone,
I completed tutorials and i tried to get a value from characteristic and i tried to do something extra. But i am encountering a problem which i could't understand...
hello.
My first nRF9160DK is 0.8.2 2018.49 and all demos goes well on it.
My second nRF9160DK is 0.8.3 2019.1 but none demos goes well on it except at_client.
Is there...
Dear all,
I want to know the methods to analyze Bluetooth 5 protocol, such that these packets sniffer tools: BLE USB Dongle from TI or nRF52832 DK.
Which one is better...
android OS: 6.0.1
nRF Connect: 4.22.3
nRF5 SDK: 15.2.0
Hello
With the nRF Connect For Desktop and also with the app on iOS, it works perfectly to perform buttonless...
Hello,
I understand reading your documentation that the nrf5x series have support for RPL but i can't find the implementation in the SDK 15.3.0.
Is RPL implemented in...
I am working on a project to do serial uart dfu in nrf52810. For that purpose i will be writing c code equivalent to nrfutil. I was going through all documentation and tried...
Hi, guys. I'm using PCA10056 and SDK 15.3's BLE UART peripheral example.
I also have a Microsoft HoloLens (the first version which runs Windows 10 and the HoloLens shell...
Hello
I am working with LIS2Dh12 accelerometer sensor interfaced with SPI 2 of nrf52832. For its one of the axis we have configured the interrupt which is working fine individually...
hi,i am using nrf52 DK kit. i have interfaced it with bmd 101 ecg sensor. The sensor sends continuous data over UART. I am using SEGGER IDE. The code which i am using is ble_app_uart...
