Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
I'm testing concurrent ESB and BLE with the MPSL Timeslot API on a seeed xiao nrf52840. I've created a minimal reproduction based on the `esb_prx_ble` sample from the nrf...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Dear Everyone, We're using the PAN B611 evaluation board (ENW89861AXKF) which features a PAN B611-1C Bluetooth Low Energy (LE) module which is based on the Nordic Semiconductor...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I'm trying to make the initial connection and flash/debug my adafruit NRF52840 express through a Jlink EDU to SWD on the NRF board. I am trying to flash to the board in the...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi,
We are trying to install the nRF toolchain/SDK/SES etc. so that we can compile (modify for NB-IOT) and evaluate the nRF91 asset tracker.
We have followed all the steps...
I am trying to use a button to put the nRF9160 to sleep and to wake it back up.
I configure my button as follows:
gpio_pin_configure(dev, PIN, GPIO_DIR_IN | GPIO_INT...
Based on mesh3.1 sdk15.2 Can I add DFU service to light switch server? Used to upgrade firmware via APP nrf Connect? I added a dfu service to the light switch server with...
Hello,
I wrote the code for HT1632 using SPI Protocol
while debugging when it comes to below function it will stop debugging
HT1632_5X21_init( LED_MAX_DISPLAY_X, LED_MAX_DISPLAY_Y...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Currently with one device...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using FDS module to write into Flash. I...
Hi there,
I' d like to develope dfu by receiving byte stream (mimeType) over USB or UART
I am almost newbie for developing dfu.
I already checked dfu over ble and...
Dear Nordic,
I try to compile the Keil project inside the thingysdkv210.zip file but it does NOT work.
I use Keil uVision V5.24.2.0 on Windosw 8.1.
There are so many...
Hi,
the evalboard seems successfully implementing the command start_rx_sweep by placing the receiver in the sweep mode.
infocenter.nordicsemi.com/.../nrf_radio_test_example...
Hi,
I am trying to connect with nRF9160-DK to our local network. After first restart of the device I was able to connet to the network, but straight after that Asset Tracker...
Hey, I am trying to incorporate an app timer using the app timer function already on the code in the central and peripheral examples of the SDK for the UART examples. Specifically...
Hi Nordic,
I have old NRF52832 product which is developed by SDK11.0. The bootloader start address was set to 0x79000. Now We want to upgrade the it firmware by using...
Hi,
i'm using BLE MESH 3.0 Light Switch Example code. i want to send Light on-Off command every 2 second Timer base instead of Button press.
i got an error below.
