NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
I saw this post for SDK v12.2:
The FDS requires data to be word-aligned
devzone.nordicsemi.com/.../how-to-force-word-alignment-for-fds
Is that still true for...
Hi,
My target is to update the application firmware running on the nRF module using serial wire connection.
I currently do experience the issue, that DFU process completes...
I am in the initial phases of porting an arduino project using the NRF52832 to the Nordic SDK (14.2 for the moment) and am running into issues when using TWIM and an event...
Hello
Im trying to figure out where the health model client sends the health messages. Ive tried doing prints in all of the send methods in health_model_client.c but not...
Hello,
I'm having an issue when I try to connect to my device from an iPhone X. I'm using SD132 v6.0.0 on SDK 15.
The phone tries to connect and then it times out. All...
Hi!
After connected and get log info "Connected." I start bonding:
but there is no any success message.
Therefore nRF52 SDK15 can't to made secure bond.
Why?
Hi,
I'm using the light_switch example to implement mesh. How do I display the RSSI value of server on rtt viewer when the client receives the server status?
Regards,...
Is it possible to modify BLE_CONN_CFG_GAP after the softdevice has been enabled? I want to be able to set the event length on start up based on a setting stored in flash with...
Hello everyone, I am looking to make a small tracker using nRF52832 chip. Can anyone please suggest me a board and a coin cell having very small dimensions so that my tracker...
I am looking for a solution to create a very low latency (<10mS) audio link for continuous streaming.
Is the proprietary mode on the nRF52 series able to do that?
Is there...
hi
In Provisioner
in function app_default_models_bind_setup()
check the following lines
/* Bind health client to App key, and configure publication key */ ERROR_CHECK...
Hello,
I am creating a project through the MultiLink example.
One problem occurred. If the device is attached to NRF52DK, the connection will be disconnected immediately...
Hi,
I am running nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_hid_composite and find it can work in standalone mode. However, if I go to Keil or IAR debug session...
I created mesh networking using mesh SDK v2.0.1. And I have connected mesh to PC and smart phone.But it's a pity that the client can't receive the servers' RSSI (although...
