i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hello,
we are facing a weird issue with a few models of smartphone since we increased the max MTU size. We are testing at the office with the Xperia E6553 but the Samsung...
Hi there
I am stuck. My incremental wheel with photocell and comparator circuit does not work if the QDEC hangs on it. But seperately it works fine.
When I hang it to...
Hi Team,
Which models are supported in the latest mesh SDK?
I can see support for the on-off model.
Is Time and Scenes (Explained in Mesh Models.pdf, Section-5, Page...
I use SDK13, nRF52, S132
I use bootloader_secure_ble with generated public key for bootloader and for nrfutil. After all steps like discribed on
devzone.nordicsemi.com...
Hello.
I use nRF52832 and power from 3.3V source. Also I use the accelerometer and gyroscope with VDD 2.5V and 3.0V respectively. They are connected to nRF through SPI....
Can a device that is configured and programmed from Keil (softdevice, application, bootloader) be updated with code that has been compiled on ses (application)? I have converted...
Hi,
Referring to bootloader programming article - there's a post-build phase of programming UICR.BOOTLOADERADDR
The article describe how to use nrfjprog to do this which...
Hello,
I studied the "gpiote" example in the SDK. In order to fully understand how it works, I attempted to modify the "template_project" example and follow the process...
SDK：【nRF5_SDK_15.0.0_a53641a】【examples】【ble_peripheral】【ble_app_uart】【pca10056】【s140】【arm5_no_packs】
Before downloading nRF Connect ,the results of my scan is
【service1...
We are using SDK nRF5_SDK_13.0.0_04a0bfd with the NRF52832 chip. Using peripheral role, the nRF is fatal crashing right after connecting with iOS nRFConnect (and our custom...
Hello. I have discovered similar questions, but it's still not clear for me. I also have cheched pwr_mgmt example, but as I understand all operations with power mode in board...
I recently upgraded from SDK 11.0 to SDK 14.0 and am seeing much slower connection speeds from the new SDK. The old version would connect in about 400ms, but the new SDK takes...
I would like to measure the VDDH voltage (lithium ion battery) on a nrf52840 with the power fail comparator.
If the voltage drops below the threshold, I want to reduce the...
Hi all,
we are using NRF52810 and SDK 15.0 (our own custom board)
working on ble_app_uart.c example.
we are able to send / receive 20bytes(approx).
we need to transfer...
