Hi,
We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM.
We have already consulted with you regarding the design under Case ID...
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
I am using the SDK v3.4.0 LTS
for modem error debugging I included: prj.conf
I am mapping errors depending on wether memory allocations failed.
I am fetching the stats...
If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
Hi,
I am developing firmware on the nRF93M1 DK and have a question regarding the Wi-Fi location feature. According to the Nordic documentation (Features of nRF93M1 — nRF...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
hello I am new on nrf52 and I would like to run the example for the ant+: "bpwr_tx".
I am on a nrf52832 chip (with a pca10040 1.2.4 demo board ), I am using nRF5_SDK_15...
Hello,
I used nrf52832 as a scanner.
Now i use it to scan only one tag. And the TAG advertise data addcoring to ble 4.0.
Now i find scan channels are not 37,38,39,37...
■Development environment nfr52832 SDK_12.3.0
■Question I'm making Central's module. After connecting with a peripheral of pairing finish, the function(pm_peer_rank_highest...
Hi all,
I am trying to test OpenThread protocol for an application that we have and we want to use the CLI interface as the application logic should stay in the application...
Hi all,
I was in the process of buying 3 nrf52-dk boards. I need to know if one can differentiate all of the different boards on their PC when connected at the same time...
Dear Nordic Team,
Thanks for support
Currently i am work with VL53L0X in ble_uart_app example. it working fine , but its take 5ma current. How can i use TWI in low power...
Hi,
I would like to know if you can sniff BLE packets with really low transmission power, for example can you sniff a -35 db signal with any average bluetooth receiver?...
I've used PCA10040 sdk15.0 example ble_peripheral ble_app_uart
I can handle it through terminal.
If I insert strings through terminal, App can receive.
But, I...
hii,
i am trying to interface the nrf24LU1+ and nrf52832. I wanted to know if i can program the nrf24lu1+ without the requirement of nrfgo motherboard. or is it necessary...
I don't want to use MESH， because there are too many data
Application scenario
Mobile phone ------------> DeviceA --------------------------------------> DeviceB
...
Hello,
Would there be any particularly adverse side-effect if two NRF51822 GPIO pins (e.g., P0.18 and P0.19) were shorted together? One of the pins (e.g., P0.18) would be...
SDK ：15.0.0
Examples：ble_peripheral / ble_app_uart / pca10056 / s140
Board：nRF52840 DK
After pairing, may be connected, because the indicator lights continue to shine...
Hi,
I am using sd_ble_gatts_characteristic_add to set a characteristic in my service. The function call return 0 - NRF_SUCCESS but when I browse the service with nRF connect...
Hello,
I try to add pairing functionality to my app. Error code NRF_ERROR_INVALID_PARAM occur from the sd_ble_gap_sec_params_reply when i want to read my characteritic...
