I am using the nRF52840 dev kit, I have setup nrf connect sdk v3.4.0 and v3.4.0 toolchain, signed up with ANT and added ANT to my west yaml file. The first issue I had was...
we run long-term HIL tests with typically 3–8 nRF9151 DKs:
DKs spaced only about 1–3 cm apart
short USB 3.x cables to powered USB 3.2 hubs directly below them
sometimes...
Hi
Our project uses the nRF52833 SoC without an external PA. During the Korea KC spurious emission certification, the out-of-band emission on the first channel in DTM 2...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
1.What is the maximum rate that the QSPI of nRF54L15 can achieve? 2. Is it possible for me to use QSPI to read the flash memory while simultaneously refreshing the screen...
Hi,
I want to ask if the Nrf54l05 supports application image compression. I asked Nordic AI and they said it’s not supported, but I want to know the reason why it’s not...
Can anyone verify what two pins are used for NFC on a FANSTEL - BM20C module? I've been in contact with Fanstel for over a week, but they haven't given me a definitive answer...
Hello, We are trying to use the debugger tool on Keil for the nRF51 DK, But we are having a really hard time to figure out how to make it work. Do you guys have a tutorial...
Hi,
I am developing my own program based on serial example. Project is based on gcc compiler under eclipse. I have preapared my own board with rigado module (nrf52832). HW...
Hi!
SDK13, nRF52.
I try to use FDS storage to flash and always get FDS_ERR_NO_SPACE_IN_FLASH.
What shold I check for normal work?
Now I have next settings:
#define...
Hello,
We are having a peculiar issue with the NRF52 and SDK 13 that I hope you might be able help with.
Having migrated from SDK 12 to SDK 13 with softdevice 4.0.2, we...
Hi,
Im having nRF52 DK and im using CLI example....i have configured through the putty by seeing this https://devzone.nordicsemi.com/f/nordic-q-a/22261/cli-autocomplete...
I implemented DFU secure ble. And implemented encryption. But now I remarked strange behavior. If make same DFU packet (.zip) and flah nRF52 than update firmware for same...
Hi,
Im running CLI program in my nRF52DK.
Im unable to connect using UART or USB as the transport layer for the CLI module but i can able to connect using RTT as the transport...
Hey!
I have some trouble service UUID then i try to use the multilink central example project on a nRF51 dongle. I want it to have contact with a peripheral with sends a...
I'm trying to get a Bluetooth interface (Bluefruit) to the Nordic BLE softdevice under NuttX. Right now it's very unstable. It will work occasionally for 90 seconds and then...
Hello,
When trying to connect to our custom board, it ends in Time out after 5 seconds.
On the board, I put the simple Nordic_Blinky example (\examples\ble_peripheral...
For the custom_ble_service_example , trying to change the service used in the example to a Bluetooth SIG service.
Original is: CUSTOM_SERVICE_UUID_BASE f364adc9-b000-4042...
Quick question: when will the nRF52840 DK available? On the nRF52840 DK page, there is a recommendation to avoid the PDK:
"The nRF52840 replaces the nRF52840 PDK which is...
I have the super typical problem of needing long data transfer greater than the 20 byte MTU size.
I have a basic protocol that has the total length of a long message coming...
