It flashes with sucess
C:\Users\vasco>openocd -f interface/stlink.cfg -f target/nrf52.cfg -c "program \"C:/Users/vasco/OneDrive/Ambiente de Trabalho/zephyr.hex\" verify...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hello,
We have the following Problem to solve in general:
A device should control the exhaust system in a vehicle.
This device needs to retreive the engine RPM using a...
Hi
I have a brief question to which I'm not able to find a clear response: When the SD send a notification of a change in a service value, this notification has a confirmation...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Hello,
As far as I can tell, the NUS app sends a signed char of value -127 to 127 in decimal. Is there a way to use the stock UART application to send an unsigned byte...
Hi Noridic,
I follow the Application note Nan_36 and download the nrf51-ble-app-lbs project as a practice, but the compiling is not smoothly with SDK 9.0. I finally fix the...
Hello,
I am working with S110 stack and the custom application. I wanted to use the ADC driver with blocking and interrupts enabled. But the application is blocking and...
Hi, I use NUS quite alot with the following condition;
(SDK 7.2 & S110 7.1 with IAR 7.1)
When the peripheral only uses NUS, iOS cannot detect the peripheral at the ...
Naive follow up to What is NUS? .
Is NUS merely a vehicle for tutorials and fast prototyping? Or can it be used to build real world apps on?
If so, do we rename the...
Hi All,
We are in design phase of our project . We would like to use NRF52832 for our project.
Our project is a wearable based on BLE. We are planning to use RTOS in NRF52...
I am starting to port the example
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_peripheral\ble_app_hrs to my board. I haven't made any change to the example to save something...
Hello, I have a problem when I attempted to increase timeslot length with 10 ms ,every time I received NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_FAILED signal.
Why can't to extend...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE.
If the program is wrong,The chip will reset,
I want to save some data to the FLASH area before the chip reset.
What I need to...
nRF 8001: How to use it in Beacon mode where in no pairing or Bonding is required and
it only transmits some information which cn be received by any phone that comes in range...
