Hi, all:
I use 9160DK to test GPS standalone mode as follow steps with AT command example:
Approach 1:
1、set ”AT+CFUN=0“ to power off mode;
2、set " AT%XSYSTEMMODE...
Hi,
Could someone point me in the right direction for changing the clock speed on the nRF54h20?
Can this be done via DTS or is there a nordic API call that I can make...
Good morning,
I am try to build a application from example list, Bosh bme680 with supported board rak4631_nrf52840, and I am receiving a error message, but if I try to...
I am working with the "TF-M secure peripheral partition" sample project ( nRF5340DK, NCS v2.5.0, nrf/samples/tfm/tfm_secure_peripheral ), and modifying it as necessary to...
I try to use st25r3911 and try to achieve low power consumption.
The code configures interrupts: gpio_pin_interrupt_configure_dt ( & irq_gpio , GPIO_INT_EDGE_TO_ACTIVE ...
I am trying to measure the battery voltage on my custom board which is based on the nRF52832 device. I am using nRF Connect SDK 2.7.0 in VS Code. The dts file for this custom...
We are able to update the firmware of our nRF device over BLE using the nRF Connect mobile app.
However we're looking for a solution to replace the nRF Connect app with...
I'm working on a project that involves an nRF8001-based device as a Bluetooth Smart slave, in combination with master-side software running on an iPhone.
When the devices...
Hello
I have written some code to write the nrf51822 via SWD. It all works, but I would like to make it faster.
I am currently writing one word at a time. If I read...
Hello dear friends,
I'm trying to bring up a Raytac module for the first time. I was able to program S110 7.1 and I'm using the Beacon example found in the SDK 6.1
But...
Is there a similar way tot get the radio's MAC address when using Gazell only (no BLE)?
In SoftDevice there is a "sd_ble_gap_address_get()" function call.
Hello All,
I'm trying to program a NRF51822 module for the first time. I'm using the Jlink for ARM from IAR which is segger rebranded. It supports JTAG and SWD.
We got...
Hi,
I am trying to obtain a 10khz PWM (50%) on an output using Timer2 (see code below). It is working fine up to around 500Hz (2msec), above that (1kHz) I am getting only...
I would like to develop an application with nRF8001 DevKit. The master emulator of this kit is an USB Dongle and it is originally meant for PC connection. My final goal for...
Hi all,
Problem: Second harmonic with nrf905.
I used nRF905 and exact recommended design&layout in the datasheet. Now, it is said that there are 2. order harmonics ...
It seems that the all the msc_inline_*.png files are missing from the SDK 6.1.0 documentation directory.
For example:
file:///C:/Nordic%20Semiconductor/nRF51%20SDK_v6...
Hi,
I use NRF51822 as a transmitter in "gazelle mode" so no soft-device is enabled. At the other end I use NRF24LE01 as a receiver. In order to see what is going on in...
Hi All.
I made a nRF51822 based PCB with SWD header but I don't have any J-Link lite to load Firmware.
I have a nRF51822 Eval Kit. Is there any way to use the J-Link of...
Hi,
I am using nRF51822 and I compiled and loaded uart example code. Also i used nRF toolbox android application on samsung s5 with android 4.4.2.I am using sofdevice 6...
Hi All,
I would like to broadcast 256 byte data in one shot every second, any reference in SDK recommend?
Thanks in advance.
**updated at 19 Sep, 2014
Application...