So I need to decrypt a single 16 byte block of data using AES128 and a pre-shared key on the above SoCs. But PSA doesn't seem to work (I'm currently working using the nRF52DK...
nRF52832, SDK17.1, s132 I work with SPI and it works on the this project with SDK15. But I have transferred this prj to the SDK17.1 and I can't make SPI work. I don't get...
Good Afternoon,
I am working on getting the npm1300 up and running on my custom board. I have a 1v8 line and a 3v2 line with the load switches being used as LDOs. I am using...
Hello,
I'm currently working on a fitness tracker application using the Nordic nRF7002 DK board, paired with an analog MMA7361 accelerometer , and a round GC9A01 SPI-based...
Hi,
We have experienced some unknown resets in our devices specifically when woken up after being in storage for a prolonged period in ULP mode - about a year or so. Afterwards...
Function: Now we have developed a function similar to usb file upgrade on the application side by ourselves (which requires operating bank1, writing the Settings page, involving...
Hi,
I am almost done with my code for channel sounding with multiconnections. It all works, but somethimes i get this after a certain period of time: This Warning pops...
I am new to Bluetooth 4.0 and want to use for a specific application. I intend to modify the Bluetooth 4.0 protocol and would need continuous transmission of packets. Is it...
hiii....
i am using lightblue app in i phone to connect with the advertising device...in my ble profyl i have 5 services and 5 characteristics in each... most of dem i...
I make a call to sd_ble_gatts_hvx, and get an error. The call produces an error and I end up in ble_debug_assert_handler
From ble_debug_assert_handler:
The file name is...
Hi,
I've tried to implement s120 softdevice (version 1.0.0 production ready) on NRF51822 Development Kit and run ble_app_multilink_central example from sdk 6.1.0 on it but...
My devices should be able to "see" each other and at the same time they should be able to extract some information from a received Advertising packet. After reading about...
Hi, I use s120 stack. Peripheral device sends a notification 6 in a row, but the central device receives only the first 3 notification. How to get all the notifications?
Hi,
I have 2 pins with PULL_UP in sense mode and when i use sd_power_system_off() i measure 25mA current, which is higher than when my system is on (around 10mA)!!
How...
We are using an nRF8001 with bonding. We are trying to figure out how big the dynamic data is that we need to store (since we are used a fixed-size storage in flash memory...
I just received my Beacon Kit and need a programmer/debugger but money is tight. These are the options I'm looking at:
cut the traces on my nRF51822 EK board and add...
I wrote an application that works using an Enhanced Shockburst-compatible protocol (because I need it so), using the RADIO interface.
What happens if a packet with an address...
Hi U guys
First I’m pretty new I use of bluetooth low energy, so bear with me.
It is pretty simple, I need to send a temperature each 10 sec. or whenever it has changed...
Hello. The nRF51822 Series Reference Manual says on page 38, "The SWDCLK pin
has an internal pull down resistor and the SWDIO/nRESET pin has an internal pull up resistor...
Tunning connection parameters to minimize current consumption for a fitness device transmitting data to ANT+ and BLE at 1sec intervals.
The desire is timeout after 60sec...
Hi,
We are trying to use the over-the-air bootloader in our application.
Our problem is the bootloader seems to require one first over-the-air download before it allows...
