Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development, and we meet some problems:
1. when the matter.ota is 1003KB, takes about 10min30s to...
I have followed the instructions in the DevAcademy Cellular IoT Fundamentals Lesson 3 Exercise 1 exactly, (whilist filling in the gaps from the cloned cell-fund repo) and...
I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Hi there,
We have a device that utilizes an NRF52840 chip. Several threads on DevZone - including this one and this one - warn about the dangers of applying voltage to a...
Using FreeRTOS and SDK 15.3 on nRF52840 and SES, SD 140
I'm following along with the NUS example project in this particular release and have a problem I'm a little stumped...
I'm developing firmware for a RAK4630 for IOT purposes. According to the datasheet, the average consumption of the nrf52840 is 1.5 ua in system ON mode. Mine is measuring...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
Dear Nordic company,
I am writting to you in order to get some information about buffer sizes in your aplication. I think, I am bale to modify buffer size and maximum...
I am designing an application using the nPM1100 and I would like to know if I can use the VSYS as a power supply pin for my other circuit.
Is VSYS supplied by the battery...
In the nrf_sniffer_ble.sh script, the block that checks for an active virtual environment uses the following line:
if [ ! -z " $VIRTUAL_ENV "];
Notice that...
Previously, I compiled and downloaded the radio_test example into two DK boards.
I then used the CLI to set the parameters for each board one as TX one as RX
On setting...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
We are using the nrf52840-based module in our product.
This module is already certified with BT SIG.
Do we still need to certify our product with BT SIG certification...
Hi, As I am working on nRF5340dk and I am facing issues with flash memory. My application is exceeding the size of flash in nrf5340 (1MB flash). I want to move to nrf54 series...
This is a continuation of my previous thread ( Connections drop and don't come back (and "SoftDevice Controller ASSERT: 53, 296") ) (Case ID: 341823).
The project is a star...
Hello,
I am using Zephyr Toolchain v2.9.0 on an nRF9161 custom board . I have updated the modem firmware to mfw-nr+_nrf91x1_1.0.2 and flashed the board with the hello_dect...
Hi to you all. I have a question about how I can apply this mechanism in nRF52.
In modern TWS, it works like the phone or PC connects earbuds separately and sends and receives...
Hello, i'm having a problem with the satellite detection time when I start gnss search. When I start the search, for a while at first the satellites are not detected and then...
We are making a board with nrf9161 and nrf54L15 so that we have the GPS tracking facility and BLE . We wish to connect (send) other devices' data to this device (like temperature...
Hello,
I am testing the "peripheral_hids_keyboard" sample from the Nordic Connect SDK v2.9.0 using the corresponding toolchain version. When connecting the device to an...
After I added the device on the Samsung platform, I shared the QR code, and then added it with Apple, but the device could not be found.The log prompt is as follows:
For a project running a BLE connection and sharing data via the NUS service, we have seen that setting up Coded PHY (S2 or S8) will eventually produce an assert error as follows...
