Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
We are planning to develop an Matter door lock which includes NFC/RFID, Audio, keypad and BLE functionalities used separately. I am considering using either the nRF52840 or...
I tried setting the VDD voltage in the 9161 DK to 3,3 V, but it remains at ~1,76 V.
I'm able to enable/disable the GPIO extender just fine, so at least reading & writing...
I have had great success developing a project based on the peripheral_uart sample. Now I am trying to add DFU over UART to that project. Specifically, I would like to add...
Hi,
I have the following minimal example:
main.c
proj.conf:
Now, when setting CONFIG_SERIAL=n my nRF52840DK drains about 3-4 µA, when setting CONFIG_SERIAL=y it...
I am attempting to use the automatic WiFi connection feature described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/wifi_mgmt_ext...
Hello,
I'm trying to merge together a couple of sample projects to make a prototype (in particular, the LTE-BLE gateway, and AWS-IoT samples) - to run on the nRF 9160DK...
I used nRF52840 board with SDK 17_1_0 ,
VL53L5CX driver I want to transfer large amount of data on I2C but when i try to write it then first time nRF52840 restart and after...
Hi,
What is the correct way to build an application (say asset_tracker_v2) included in a newer SDK (2.6.1 for example), using a nRF9160 DK without on-board SPI flash device...
Hi,
I have a bunch of openthread routers and TTM shows one as in some error state.
RLOC is 0x9400, but no ext address is shown.
Also a child connected to this router...
Hi everyone,
I am planning to use the cadence/publish interval property within a mesh network. I can not find any examples on how to use it. I know I can set it in the nrf...
I'm developing a BTLE sniffer app to run on a headless raspberry pi 4 with html/php/js access. The application runs well on the development platform - Ubuntu 22.04.
On the...
We have some custom hardware that utilises an NRF52832. Up until recently, all our firmware was built on NCS V2.2.0, which I believe used Zephyr V3.2.99. We have implemented...
Hi,
I am moving to version 2.6.0 of the SDK and toolchain. I am developing on windows 11 pro. Our cMakeLists.txt file creates a version file in our conf directory version...
Hello,
We have a custom board using a nRF5340.
We followed this course implementation for simple serial recovery over UART (and also tried CDC ACM) but as soon as activate...
Hi, I am trying to download all software necessary to program nRF chips. I am following this academic course Lesson1 When i try to install nRF connect SDK after toolchain...
