Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
Hi all,
I'm currently testing my Mesh network on a small scale. I'm sending messages every 25ms with different TTL values in an environment as visualised below.
The...
Hello,
I'm currently using an nRF9160 DK v.0.7.0 and the provided samples like the asset tracker and the at command client. Compiling, flashing etc. of the firmware already...
Dear Sir/Madam,
Can nRF Sniffer fetch the data of BT Classic Devices having any BT Version from BT 2.1 to BT 5.0?
Kindly help me on this issue
Regards,
MIHIR TAIL...
(running a mesh 2.1 sdk)
I am provisioning my nodes over serial and do not need the GATT Provisioning service. I need to access the GATT Proxy service to send mesh data...
I want to upgrade FW.
Android app has done. but only iOS encounter some problems.
First, I try to download nRF Toolbox on Github. result is DFU Service not found .
I...
Hi,
As per subject I am looking to implement hardware on-the-fly AES-CCM encryption/decryption of ESB packets. Are there any examples/guides available for the nRF52840?...
Hi,
With the PPK PCA63511 we have tried different PPK software such as python 1.1, nRF connect for desktop.
In that process we observed that current measurements are...
Hi. I have a problem with using RS485 (ISO-3082DWR) from NRF-52832. The SDK version uses 15.02. Here's the code I've run. nrfx_uart_config_t uart_config =
{ .pseltxd = 30...
Hi,
I am working on a project in which I use the USB_CDC_ACM profile. I have mainly taken the example you provide and add the rest of my code.
Everything is working fine...
Hi Sir
Do you have any suggestion for transfer file from PC to QSPI external flash ? over USB ? please teach me how to start.
I need a simplest way for put file to external...
