After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
Is there a possibility to change the COM port number of the nRF52840 USB dongle manually?
I already looked in the device manager under the port tab, but couldn't...
Hi all, I have a prototype device app I'm going to "deploy" in a remote location with an nrf52840 dongle. Initially ble via special shell commands added to nrf/samples/bluetooth...
Hi all,
I'm new to embedded programing with Nordic I'm using the evaluation of Fanstel EV-BC 805M. I was trying to program the basic program for blinky led, however by the...
Hi,
General information:
nRF52840 SoC
Our own PCB’s with inverted F-antenna
nRF Connect SDK v1.8.0
We are in the middle of approval testing our product. We have...
Dear all,
My application is build on nrf52, nrf connect SDK v2.0.0.
For energy saving purpose, I put the nrf52 into sleep mode, using these code
And wake up via GPIOs...
Hi,
I need to transmit and recieve data over the 2.4GHz radio. I have customized packets to be sent and received over the radio. But I dont want to use ESB or Gazell protocols...
Hello there,
I want to use the nrf52-DK with pc_ble_driver_py. According to the 52832 compatibility matix ( link ) , Revision 3 of the soc needs S132SD v6.1.1 at least....
Hello,
We have developped a product with the nRF52832. Basically, it is a power sensor that uses both BLE (advertising) and ANT+ to send data regularly to a display (third...
Hello, I have a question about the scan request event.
I checked the logs of BLE_GAP_EVT_SCAN_REQ_REPORT. If this event is received, does Softdevice recognize the packet...
What a pity ncs ota not support single bank, but old nrf sdk support.
I know mcuboot not support transfer image over bluetooth, i want to know if there are any other way...
NRF SDK 1.9.1
Modem Firmware 1.3.1
I currently have a production device out in the field that is connecting to a specific cell tower and has the ability to then connect...
hi
I want to use two i2c
But in devicetree add &i2c0 and &i2c1
but it shows undefined reference to `__device_dts_ord_131' and static assertion failed: "/soc/i2c@40004000...
Hi,
I try to advertise nrf52840 dongle on pc to build a connection with nrf5340 uart service. Although I try to modify the advertising program by advertising.py and heart_rate_collector...
Hello there
I need to dynamically initialize and uninitialize the USB HID in my application. Because there is a condition on which I don't want any PC to recognize my device...
