I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Hello,
I am using an nRF52833 dev kit and the Zigbee light_switch example from nRF Connect SDK.
I was trying to implement the sleep mode so I wanted to estimate the power...
Hello,
I am having an issue with board bring up for a custom board I developed using the nrf5340 processor.
I have created firmware based off the peripheral_uart sample...
Dear Nordic support team,
I bought 3 piece of nRF52-DK from MOUSER, 1 piece of nRF52-DK version is 2.1.0 , and another 2 piece version is 3.0.0.
nRF52-DK version 2.1...
Hi there,
We're using nRF52840, IAR 8.40.1, nRF5_SDK_16.0.0_98a08e2. My question is, I need to toggle a GPIO pin right after SPI finishes the TX transaction and right before...
I am trying to use both USB and BLE on an NRF52840 using SDK 15. It hit a hard fault during initialization, specifically when it tries to enable the USBD IRQ.
It looks like...
I am familiar with the PTCRB certification process for an IoT device incorporating a certified module. https://www.ptcrb.com/wp-content/uploads/2020/08/10_Steps_to_PTCRB_Cert_for_Cell_Enabled_IoT_Devices...
Hi, all
How to enable and set fast advertising and slow advertising in NCS.
We always set advertising parameters in legacy SDK like below, how to implement it when using...
Hello All,
Thank you for reading my post. I have finished developing a small battery powered device I have been working on and just completed programming the functionality...
Hardware: nRF52840dk
SDK: NCS v2.0.0
application:
Calling bt_encrypt_be() during OpenThread network traffic hangs the device when using MPSL with OpenThread 1.2. ...
Hello everyone,
I'd like to build a Relay Node in Light Switch Example but I don't know how to implement firmware.
Can you support this for me? Thank you so much.
...
Hello,
I need to build a project in a Docker container. It built fine under Windows 10 with a connect SDK v1.9.1.
Now I am using a Docker image built with the Dockerfile...
Hi,
I am trying to update nRF5340 netcore application, but i don't know how to start.
Here is what i tried:
1. I created two custom applications for nRF5340 appcore...
Hello DevZone,
I want to transmit some connection information such as a Bluetooth address serially to my peripheral and have it add it to its whitelist.
I have read a...
Hello,
I'm am trying to use the UART0 bus on the network core at the address:
uart0: uart @ 41013000 {
compatible = "nordic,nrf-uarte" ;
reg = < 0x41013000 0x1000...
Hi,
ubuntu 20.3
vscode + nrf connect
when i creat project from sample code unicast_audio_client, i get the following compiling error message:
* Executing task: nRF...
