Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi, I am new to working on the display . I am trying to integrate nrf5340dk board with waveshare lcd module which is of 1.14 inch and has st7789v controller by using SPI communication...
Hi,
Legacy SDK bootloader and dfu preparation workflow had the following option:
hw_option allowed for checks, whether supplied firmware matches given hardware. So firmware...
Using nrf5340 audio DK & ncs v2.60
I modify this function to print this information when the number of packages reaches 100.
\
Part of the result:
120*100*8/(...
Hi, I'm trying to implement timer synchronization on one central and multiple peripherals, I'm using nRF52840 and NCS v2.8.0. I've seen the example conn_time_sync which uses...
Hi,
I am using download client for downloading a file.
I am using download_client_get and get fragments in callback.
When the file requested is short in the callback...
Hello Nordic Team,
I'm developing a project with two nRF52/nRF54 microcontrollers where I need: - 1st microcontroller as BLE peripheral receiving mobile app data (nRF connect...
I'm migrating code from ncs 2.7 to 2.9.
I am using CONFIG_BT_EXT_ADV and scan timeout callback - such timeout requires CONFIG_BT_EXT_ADV:
It was working fine. Now it's...
Hi,
I follow the custom board exercise steps with mynRF52840 DK and when I reach step 8.1 , in the deviceTree visual editor, I notice that the GPIO0/1/TE options under ...
Hi, I recently updated from NCS 2.6.0 to NCS 2.9.0 which had lots of changes. I believe I ported from child_image to sysbuild with success, as my main application on app core...
Nordic has changed the API of nrfx nrf_modem_dect_phy from SDK 2.7 to SDK v2.9.
In struct nrf_modem_dect_phy_callbacks there is an additional callback member stf_cover_seq_control...
Hi Team,
As mentioned in the datasheet of nRF9151, Imcuoff0 mode (MCU off, modem off, wake on GPIO and reset) consumes around 1.4 uA over VDD power supply then what is the...
Hi ,
IDE: SES
NCS version: 1.9.1
I install the development enviroment following this article. 开发你的第一个nRF Connect SDK(NCS)/Zephyr应用程序 - iini - 博客园 (cnblogs.com)
I use...
Hello,
I am trying to find a solution how to use wifi and ble on thingy91x and manage the coexistence between them, I have found a sample Wi-Fi: Bluetooth LE coexistence...
I am trying to implement the following: I have a mesh node built using the Sensor Server example for publishing temperature data. I want one relay node to transmit the temperature...
