Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello everyone,
I've noticed that the Bluetooth and ADC work great together BUT I'm having issues when trying to turn on & off the Bluetooth.
I've tested the on & off...
Hi,
I'm working on hid keyboard example. How can I check whether multiple bytes are received & transmitted after I increase the assigned no. of bytes in input/output report...
Hi,
I have a ncs project which currently has only the main.c file.
I want to create a header file and the c file to be included in the main.
What's the recommended way...
Hi Nordic Team
I've applied all the changes recommended on https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting-started/posts/nrf52840-dongle-programming-tutorial...
Hello everybody
I have some nrf52840-DKs and other boards with the same module and I want to create a LE Coded mesh with these boards, I am aware that the BLE Mesh standard...
Hi,
I am using the low power node example and light switch server example from nRF5 SDK for Mesh v5.0.0.
I have one board as LPN to make friend with one board as light...
Hi,
When I bond with a central to my device, the peer gets added to the whitelist. But I want my device (peripheral), to automatically start advertising in whitelist after...
Since mac os catalina, all command line tools must be code-signed. Your nRF-Command-Line-Tools_10_12_2_OSX distribution is not code signed, therefore cannot be installed on...
Hi all:
I found this issue happen on NRF52 with SDK v11.0. Because I measured the current increased ~1mA after enable GPIOTE->IN, is there any solution can solve it?? Thanks...
Hello,
I have two nrf52840 DKs.
I can get the central to connect based off the device name or a specific UUID but what I want is the central device to scan for the peripheral...
Hi,
I have following questions with reference to two different bootloader scenarios with my custom nRF52833 board:
1) UART based: do I absolutely need RTS, CTS for this...
Hello guys ,
I am using nrf52833 board with nRF5 17.2 SDK on KEIL IDE has softdevice as S140 wants to implement six pin authentication password on nrfconnect app in mobile...
Hello!
Sorry in advance for what is probably a very simple mistake. I am currently trying to develop a simple PCB for the nRF5340 QKAA aQFN94 package using EasyEDA (bare...
Hi,
We are using nrf52832 for ANT and BLE for which we use SDK_17.0.2 and s332_nrf52_7.0.1
Our objective is to pair and un-pair ANT sensors. So far pairing multiple ANT...
