Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
I am using nRF51822 and the Software device is S130. The application is based on ble_uart_app. I can declare it as a Bluetooth 4.2 device for lab approval. Right?
I know that Nordic has published a reference antenna design with the nRF52DK. However, I would like to develop a much smaller module with minimal antenna PCB trace or antenna...
I would need more pwm channels, than there is possible with pwm library on nrf51822 (That is 16 channels).
I would like to do it in a fashion, similar to this , using a prescaler...
To whom it may concern,
I use a BLE app via nRF52832_WLCSP, 'ble_app_hids_keyboard' of SDK11(pca10040),SD s132_nrf52_2.0.0, with the HID profile. once I started advertising...
I'm currently using CrossStudio as IDE. I've no problem in compiling and downloading the application in the nRF52832 microcontroller. However the application wouldn't start...
What is the maximum number of connection a central device can connect and control in open mesh? Is 1 to 50 possible? What is the latency?
I am comparing to RFdigital Simblee...
I am trying to encrypt a write on a custom characteristic by setting:
BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM(&attr_md.write_perm);
Then in the write event I read the...
I've tried getting a notification of subscription from a bluetooth event handler like so:
ble_evt_dispatch() is being called from main:
static void ble_evt_dispatch...
Hello,
I am using SDK v12.1.0 and I want to get the debug logs over UART
I followed the Logging Sink Configuration to enable UART logging and compiled the Health Thermometer...
Hi!
I was developing my custom service, and had a question around what kind of functionality is allowed or not allowed within a callback from the soft device or other peripheral...
Hi every one.
I am developing on S130 SDK 11 and I try to use whitelist connection for optimisation.
I have currently a working project which scan for 1 sec for any BLE...
My application is based on the ble_app_uart demo. I want to get the BLE approval from the lab. The lab want me to tell them the Bluetooth profile of my application. How can...
Hello,
I am trying to interface the STPC16CPC26 with the NRF52832. As per the datasheet of the display driver, we have to toggle two IO pins from the NRF which shall be connected...
I want to write protocol stack and my program to 518222 and now need the manually download device or the automatic download device. can you offer me the communication ways...
