I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
HI,ALL
there are two 'uart_event_handler' function in the project.
one in main, and the another in the app_uart_fifo.c
with the source code, i think when i input...
Hi everybody
I make an application which combine ANCS and NUS services on my device (nrf51 SDK 9.0.0,softdevice 8.0) This application works properly when I use IOS device...
Could you explain why 8 reload registers exists. Its use and use case. Since I believe we need to reload every register each time we have to reset counter.
I have a rare issue where my device won't advertising as it is waiting for a Pending Flash event to clear. However I want to add a supervisor time-out to this. It is safe...
Hi ,
I am getting error in pstorage_store function .
On further digging function
if ((!is_word_aligned(p_src))) is returning the error.
What does this function check...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE. If the program is wrong,The chip will reset, I want to save some data to the FLASH area before the chip reset. What I need to do...
The example DFU project (dual_bank_ble_s110) for NRF51422 seems to work just fine on my custom board that has NRF51822. Is there a problem to use it like that if I set the...
Dear community,
I'd like to report a problem on the Direct Test Mode software provided in nrf51 SDK v6.1.0.
In this mode, 2-bytes commands are transmitted over the serial...
Whenever I try to run the following Convolution function for the 12th time in my code, the Processor is halted and I get the following Error on console:
Performing single...
According to this example, the device should be advertising RX and TX Characteristics. I also believe that when I connect to the UART app using my iphone, I should be able...
I have been successfully using my nRF52 Dev Kit (PCA10040) for the last few days. Today, when messing around with the UART drivers, I seem to have messed up the JLink-OB....
Hello,
I have an NRF51822 beacon board and two small 0.96" OLED displays (does not matter for me which one o use). One with GND, VDD, D0, D1, REST, D/C, CS and VCC pins...
I'm on windows 8 using the 1.0.1 sniffer application and wire shark 1.10.14 64bit with a Nordic nrf51 dongle. I'm using an nrf51 dev board with ble_peripherals/ble_app_blinky...
with nrf51 there is 2 blocks (block0 for softdevcie and block1 for user data and stack). I configured the system to retain RAM before going down using sd_power_ramon_set(0x00030003...
Hi,
I have a device that is configured to work in GAP central role. This device only scans for specific advertisements from specific devices. Could you suggest how I can...
