Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
My board nRF52840-DK always take several minutes to be ready after plugging usb cable in. The issue like Markus described in this ticket:
https://devzone.nordicsemi.com...
Hello !
I can see nrfutil is written in python and have a lot of dependencies and functionalities what typically need for x86 based host.
A lot of discussions about porting...
Hi everyone.
I would like to know if there is any good nrf mesh communication libraries for desktop applications (preferably C#)?
I would like to develop some desktop...
Hi experts,
I have a problem with programming NRF5340 SoC when using the NRF-Programmer tool. About our board, we use PCBA instead of NRF5340 Dev-Kit.
Step1: My coworker...
I'm moving an application from NCS v2.0.2 to NCS v2.1.0
Everything compiles properly in v2.0.2.
I think I've converted all of the pin definitions properly from the v2...
Hello,
we are using nRF9160 as Bluetooth host together with the Mcumgr Gatt service. We would like to be able to perform FMFU update using the Mcumgr library. We have verified...
Hi:
After downloading the sdk, I installed the compilation environment on my laptop and successfully compiled the at_client project. However, after the same installation...
I want to implement a sophisticated peripheral that implements a keyboard, mouse, and raw HID interface via USB and BLE.
I haven't found composite HID examples for USB or...
Hi,
When I try to build the ESPI sample using west I'm getting the following error:
Can you please let me know what the error is? I tried looking up the issue, but couldn...
Hello Nordic Team,
While going through this page on peripherals used by Softdevice https://infocenter.nordicsemi.com/topic/sds_s140/SDS/s1xx/sd_resource_reqs/hw_block_interrupt_vector...
Hi guys,
I want to send 'a' characters via the uart1 of the nRF52840-DK. I cut the short on the SB6 jumper to disconnect LED 2 from P0.14, which also happens to be TX of...
Hi DevZone
I just want to ask if one can use the nPM1100 with the unregulated output to the nRF9160 (which can take 3-5.5V), and the regulated output the other peripherals...
We try to get audio samples form analog or digital MEMS microphone to nrf54840 RAM memory with low power consumpion at 32kHz rate. We consider to use internal SAADC, PDM or...
hi, I want to use PPI function for timer trigger GPIOTE,
when timer interrupt comes, my output pin will toggle, but I find my code doesn't work, I think it is GPIOTE mistake...
I am trying to run the nrf/samples/bluetooth/peripheral_lbs example for the nRF5340-Audio-DK using nRF SDK v2.1.0. I am using the following command to run the example:
west...
