I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
I am trying to send "Hello" through the UART and the nrf52840 dongle using a USB to TTL approach. The main.c code and the sdk_confg.h are uploaded here. The problem...
Hello,
I love the Online Power Profiler for BLE! Great tool, very useful and well done!
I have one request/suggestion... when scannable advertisement is selected, it would...
Hi,
We develop in an OpenSuse VM so that we all have the benefit of only having to setup the tools once. Segger Embedded Studio was building our variant of the DFU Bootloader...
Hi, I am currently working on nRF52840-DK board and trying to implement simple programs. I want to toggle a LED(P0.13) on the press of a button(P0.11) but I dont want to use...
Hi,
I am trying to DFU OTA by using nrfutil with nRF52840 dongle.
I have already write nRF connect desktop Bluetooth into dongle, but when I use nrfutil to do DFU...
I am using: nRF52840 nRF Connect 1.9.1 VS Code W5500 for ethernet Azure IoT Hub
I have the above (mostly) working. My code is based on the Azure IoT Hub sample for the 9160...
We are developing a device where we would like to include the bluetooth connectivity of the device with phone, to answer the calls and to listen to audio. We are using nrf5340...
Hi,
actually we have following Solution:
- NO battery powered devices - the first nrf58240 acts as a beacon advertsing temperature values all 10sec - On our gateway, there...
Hi,
I'm trying to follow the MCUBoot + SMP SVR example on this page: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
My application uses NVS to store data and it works just fine - no errors reading or writing , and saved data persists between device power cycles.
My application also has...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Dear Support Team，
1. How to use Bluetooth Low Energy CGM service on NCS? Are there any examples for us to refer to? For example, nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral...
I turn on the device, the led turns green. And I use usb to connect it with computer then I open the nrf connect for desktop, the bluetooth low energy tool,
10:51:05.822...
Hi,
Our custom board using the nRF52840 with SDK 15.0.0 experiences a higher current draw if it starts up without the USBD module enabled at some time. The first screenshot...
