I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello all,
I have pinged the sensor on the "twi bus" successfully, now I am following the post on the read/write function that is needed to actually read the data off the...
Dear nordic engineers:
The only example I can find about flash is under zephyr/samples/drivers/spi_flash. However, the flash writing is pretty slow, and the MCU is halting...
I'm trying to record audio from Nano 33 BLE Sense which is using an nrf52840 microcontroller. But the default PDM library available doesn't allow me to record at a higher...
HI
I would like to check if it is possible to setup 3 sets of nRF5340 Audio DK as a master with two slaves.
Where the master and salves are able to send audio (via mic...
Hi All,
I would like to know how Nordic's pairing mode corresponds to the bluetooth specification.
If my smartphone(initiator) is keyboard display,and my slave(responder...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I would like to update SoftDevice from v7.0.1 to v7.3.0. Are there any areas...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
I have trouble with DFU. I could implement SMP server into my project according to your guide. (+) Add DFU support to your...
Uns NCS v1.9.1 and VSC, I am attempting to run through the Device Firmware Update (DFU) with MCUBoot bootloader exercise.
I am running to a road black in figuring out how...
I have a Bluetooth device that has a long characteristic. On previous central device projects there is usually a function like read_long_char. I am trying to get a zephyr...
We've built a device with the nRF5 17.1.0 SDK on nRF52832 which operates as a HID keyboard. On iOS and Android this is working fine, and it's working fine sometimes on Windows...
Hello, trying to get v1.9.1 lte_ble_gateway working on Thingy 91. Using Thingy 2020:23 1.4.0, which works all good with zip thingy91_fw_2022-02-17_ec486dab (tracker, nrf cloud...
Dear community,
After a lot of though and fighting with our hardware we decided to use a dual slot bootloader config with an external flash.
We based our testing on...
Hi,
I have a C++ class with code as in below:
This I need to call in a .c file, which I did with extern "C" definitions with a C wrapper as in below:
I am getting...
Hello everyone!
I am trying to add a SPI Master instance for my custom PCB, im using spi example as reference but im having a specific problem, and it is that the program...
