I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi, We have custom board files (copied from 5340dk dts files) and I wish to remove all redundant DK stuff from my DTS and free up pins. Can I remove UART0 from both the app...
I have gone through the Nordic Academy to install the tools and build the first example which is blinky. I am using MS Visual Code and SDK version 1.9.1. I have seen some...
Hi,
I use serial port example to do out UART exchange data function. But I get a problem, I don't know why? Below is my source code.
When I send 2 bytes data to...
Hi,
I am trying to enable UARTE0 on BMD-330 module. The serial config looks like this
# # Capabilities # CONFIG_SERIAL_HAS_DRIVER=y CONFIG_SERIAL_SUPPORT_ASYNC=y CONFIG_SERIAL_SUPPORT_INTERRUPT...
Hi,
I tried porting LC3 to my own 5340 project with reference to the SDK(nrf5340_audio_nrf5340_audio_dk_0.4.0), but I had a restart problem when initializing LC3
sw_codec_lc3_init...
Hi, I have a mature product that is programmed with a J-Link compact, I have 4 different PCs to program and a custom UI that uses command line instructions to flash PCBs....
Hello,
I'm currently developing on an NRF82832, I'm using a Black Magic Debug Probe to flash the firmware and the bootloader. I use Linux.
I have a working firmware...
Hi,
I started using nRF Connect SDK in VS Code recently. Everything works well, start a new Application, configure a new board, build, and flash.
While I found "Go to...
Hi,
I'm working on modifying the secure bootloader (SDK 17, nRF52840, s140) to store the old app before the new app is programmed into Bank 0 (see this other thread )...
Hi,
We have a design for a battery powered tag using a nrf52833-QIAA. I saw in a post from a couple years ago that you widened the DCCH inductor tolerance to +-20%. I...
Hello ,
I am trying to use NFC pin p0.10 as WAKE up pin , using nrf_gpio_cfg_sense_input(Btn, NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW); this code. I have defined CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I double-checked that when NordicUpdate_is_update_mode() returned false, I can still use the iOS Device Manager App to perform DFU.
I thought users needed to press...
Dear Nordic support Team
I have a question regarding the performance/specification of the RF front end of the NRF52 series chips. I noticed that the question "Is there an...
Hi, I'm testing the current consumption on a nRF52810.
I use PPKII to measure the current that the chip draws.
The software does the following.
Wakes up every 1 second...
