Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We're looking to integrate the NPM1304 in a product with a very small battery. As per the NPM datasheet we've selected a battery with a PCM.
We've previously seen...
We have a production system based on asset_tracker_v2 in V1.7.0 and V2.5.0. it normally connects and publishes fine 24/7. we have many sensors in the field. There are time...
Hello Nordic team,
I have a retail Thingy:91X device. IMEI: nrf-359404230239544
It connects to hello.nrfcloud.com, but I cannot add it to my own nRF Cloud account because...
We currently have a self-developed development board with NRF5340. The example program uses Bluetooth transparent transmission. Now I have added a GPIO pin: en_power is set...
When I was running the dm process of Connect SDK 3.0.2. I wanted to make one device as the initiator and six devices as the reflectors. I expect that the reflectors will not...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hi,
We have developed a custom board with both nRF52833 as the BLE beacon and nRF7001 as WiFi. We have chose to use patch antenna with UFL connector for both. When we tried...
Hi,
I have now run most of the YAML test successfully on the Matter TH and while I usually need to restart the TH between runs it seems fairly reliable now. Before sending...
Hi experts, I'm using the example under nrf-bm/samples/bluetooth/ble nus, and I've configured prj.conf, but it's not working.
I've been struggling with this for ages...
I am getting an error trying to get coded phy working with a sysbuild configuration for a nrf5340 custom board:
I am trying to follow the Bluetooth: Peripheral Heart Rate...
Hi,
I am using the nRF5340 for my project.
In the production stage, I am facing an issue: after programming the nRF successfully, when I perform a readback, it shows...
We have a Python script that is using pylink to open an RTT session and send some commands to the Firmware.
We have tried the JLinkRTTClient to send and receive command...
I’m working on reducing power consumption in my application using the LIS2DW12 sensor. I am currently turning off its LDO to cut power during low-power periods.
The problem...
Could you please help with providing terminal plating information for nRF52833? I have it noted as Sn but want to check if that’s matte or bright Tin.
Thank you,
Be...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
