I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello folks,
I was planning to interface MT29F4G01ABAFDWB Flash through QSPI peripheral with nrf52840 soc.
But before that, i tried to find some resource and i came across...
Hi,i'm using NRF52840 as BLE central to develop our products,the enviroment is:
SDK:16.0
SD:s140_nrf52_7.0.1
also using the third party RTOS:RT-Thread
what causes...
Hi,
I'm trying to get LittleFS up and running while also using Openthread. I've encountered an issue regarding the SETTINGS subsystem that is enabled by Openthread. I...
I'm using NRf connect SDK to compile a sample application on SES for my NRF52840 Dongle, as shown in this tutorial
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/0...
Hi,
I have some issues with auto connect after bonding.
When start advertising with my NRF52840 device, my Android phone establish connection only when the app is open...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hello,
is it possible to measure frequency from 1Hz up to 400kHz (50% duty cycle) on gpio pin having soft device enabled with Peripheral functionality? The measurement...
Hello,
I am using the RADIO peripheral to send BLE 4 advertising packets back and forth between 2 DK's (nrf52840 as transmitter, nrf52833 as receiver) following the radio...
Hi,
Nrf52 52840DK,SDK17 S140.
how to broadcasts continuous data? (Continuous broadcasting, with different data each time)
code as follows:
SDKs\nRF5_SDK_17.0.2_d674dde...
I have VSCode 1.63.0 (Universal) on macOS 12.0.1 with ncs v1.7.1 and a board with an nRF52840 MCU. I'm using the "hello_world" example. If I power cycle the board I can start...
Hi,
I'm trying to connect to hook-up a debugger in VSCode to my target but am unable to. The hardware is custom and JLink connects fine with nrfjprog to program and erase...
Hi,
I'm trying to ,create a development environment for Alexa gadget in nRF52832.
here is the thing which I'm using:
1. nRF connect for desktop version v3.9.1
2. Toolchain...
I had a Thingy91 that I think I bricked in trying to upgrade the firmware. I'm able to see the device in desktop programming, but it says erasing then gets to a 100% screen...
Dear, I am new to Nordic. I created a simple project for testing. There is a small fucntion to display "Hello World". After , Re-build Solution.. the memory used is as shown...
Dear community,
I am evaluating the nrf52 chip on the nrf52dk. I am using the peripheral_uart example, built for nrf52810. I have stumbled upon an error which I'm not sure...
