Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hello support
I have modified the cli examples and run into "undefined reference to `nrf_cli_uart_transport_api'" linker error.
The error message is
Compiling file:...
Here's my setup:
1. RPI4+nRF52840 dongle as OT border router
2. nRF5340DK running CoAP client example application
3. Wireshark running on Mac OS, with nRF52840 dongle...
Hello!
I'm trying to develop a mesh network and I've been building on top of sensor example, which has been very useful since I'm reading a few sensors. However I want to...
I am trying to generate ECC key pairs using MbedTLS on Connect SDK.
I found this code block on stackoverflow and validated from mbedtls/programs.
"mbedtls_ctr_drbg_seed...
I was trying to evluate the Periperhral ISO server, however with a NR52dk, but it returns ENOTSUP.
Bluetooth initialized Unable to register ISO server (err -134) [00...
Hi all
I am developing a proprietary radio protocol application using the nRF52805. I am not using a softdevice. Instead, this is all done by accessing the radio registers...
I have seen this question answered for the old Nordic SDK but have not been able to find a solution in Zephyr & NCS. I'm following this post on how to develop a custom BLE...
Hello,
i am using nrf52832 dev kit want to send the nrf calendar parameter through nrf connect app and send through app successfully by taking uint8_t datatype .I have receive...
Hello.
I am trying to write code to read data using saadc and write the sampled data in a micro SD card using fatfs.
I started from the fatfs example and initialized...
I'm attempting to use pc-ble-driver-py on Windows with an NRF52 DK (PCA10040) and running into the error shown below. Using the Heart Rate Collector example, the COM port...
Hi,
I'm using the ble nus uart for my application and I noticed that I was drawing too much current so I went back to the example from the SDK 17.0.2_d674dde which I haven...
I have followed the Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) and was able to comminicate with Azure IoT hub.I have created rootCA and device certificates...
This is my problem description, hope someone can help me. 1. The watch product shipped in mass production is found to be disconnected when using the mobile phone OPPO-k7x...
HI,
i have enabled CONFIG_BT_SETTINGS_CCC_STORE_ON_WRITE=y
so after power cycle the device automatically connects with iphone and the service also works fine
after this...
