I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
I have been playing with the nRF5340 and specifically the HCI-RPMSG.
I have looked at these files below. They all worked when programmed in the nRF5340.
When viewed in...
Folks,
System Info : MacBook Pro (10,1; 15" Retina, Early 2013), Running macOS 10.15.6 "Catalina", with 500GB SSD, formatted with APFS, into a RO system partition and a...
I've made a circuit using the NRF8001 but slightly deviating away from the original PCB example. I'm getting the device to go into "Advertising Started" but I can't pick up...
hello Nordic
i have s SOM which i want to use nrfutil in it for FDU via UART of an application i have on nrf52832, s132 v7.0.1
i have the bootloader flashed with the...
Up until now I have been the sole firmware developer and the keeper of the keys for our product.
Our scrappy little startup has expanded and is now bringing on additional...
Hi,
Problems I am having with PWM:
1. Using app_PWM and GPIOTE to start and stop the PWM: When button is pressed, GPIOTE handler sets a flag that is polled to start the...
I am using Timer0 and Timer with GPIOTE and PPI to output 2 clocks on 2 pins.
Both timer settings are identical (for troubleshooting). Only timer-0 can be generated at the...
I am working with nRF Connect SDK using an nRF52840 DK. And I want to realise both BLE mesh and FOTA upgrade. FOTA upgrade example SMP Server Sample works properly for Bluetooth...
To parse information from strings I want to use sscanf().
Currently I have this small test program:
And in the prj.conf I have CONFIG_NEWLIB_LIBC=y defined.
This program...
Hi, At power on lots of MUCBoot prints pop out of the UART:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1 *** <inf> mcuboot: Starting bootloader <inf> mcuboot: Primary image...
Hello -
We are developing an application for nRF52840, using the v17.0.0 SDK. The application is running on FreeRTOS. We need to power off all the RAM and use the RTC...
Hi, I am trying to get bootloader to jump to either application 1 or 2 base on button states when booting. I am not sure how do it properly. One of the applications is using...
I created an Azure IOT Hub and simulated a X.509 device using C and device SDK for Azure .
No problems here.
Then I run sample nRF9160: Azure Iot Hub and receive the...
I am using 2 counters, one to produce the 4MHz, and the other for the 62.5KHz, to drive I2S module.
I need to find a way to stop the first counter (4MHz) after it produces...
Hi All,
Currently I am using SDK_17.0.0 for nRF52832 with Softdevice S132_V7.0.1. I come to know about release of SDK_17.0.2 with highly recommendation to migrate from SDK_17...
