I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi
Im using the DFU secure example (examples\dfu\bootloader_secure\pca10028)
Im working on a NRF51822-QFAA ,S130 SDK12.3 , Im not sure about my IROM/IRAM definitions,...
Hi Nordic Team, One of our customer wants to integrate communication via Thread BLE on his IoT-Gateway. We found your nRF52840 Dongle. Does this dongle have any certifications...
Hi,
I am planning on using nrf52832 for a beacon application. I happen to get a schematic and layout from Nordic website for development.
I am attaching the schematic...
Hi, I am trying to interface MPU^)%) sensor with NRF52832. with help of BLE UART. i will get the resultant data on BLE APP. but here i got some error is this the linking error...
Hi,
we want to made the device which should working in the mesh network without provisiong procedure by user.
Typical application - network with 500 nodes, every node...
Hi, I am using nordic nrf52832 module with BLE mesh SDK V2.2.0 I want to do DFU for application + softdevice without any serial connection through mobile app between BLE mesh...
I got the fail result of the test CPS/SEN/SPE/BI-05-C [Cycling Power Control Point Procedure Timeout].
At this test, the tester does not send the confirmation until ATT...
Hi Team Nordic,
According to the AM2302 (DHT22) datasheet, the data pin will be pulled to high state in idle state. But in my case, when i am reading the data pin before...
I'm developing nFR52832 to communicate with the PC via UART. commands are sent to the nRF and for each command nRF responds with some data back to the PC via UART.
The UART...
I'm trying to include the SPI driver in my project.
I have added the .c file into my project:
I have included the path into the project:
I have enabled the SPI...
I try to make bootloader via USART for my application. I'm using: nRF51422rev.2, SDK6.1.0, S210 ver3.0.0. KEIL5.11. I did everything like describes in post here:
devzone...
I want to implement BLE security in one of my project where central and peripheral connection should be secured rather than only characteristic protection.
And any way to...
I'm developing a custom driver (C++) for the SPI master. Somewhere I've made a mistake, where the first received byte is written with a memory offset in SPI mode 1. I.e. we...
