I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Using the nrfx_qspi driver, it is possible to put a QSPI memory into DPM to save power, this all works fine and well. We want to keep the memory in DPM when uninitiating the...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi,
I was wondering what are the main differences between the different libraries included in the SDK that are meant to be implementations of ring buffers. I'm talking specifically...
Hi
I am developing a product for the health care market, and we chose embOS by Segger to by our OS for the nRF52840 Based product.
I've created a project based on ble_app_uart...
I am trying to send some data from RPi , And I am using the example of NRf Uart APP.
printf("\r\nUART example started.\r\n");
while (true) { uint8_t cr; // printf(" \r...
Hello All.
I try to build a generic function that read device reg over its I2C. I take the TWI master example of Nordic.
There is need for callback function to get in...
Hi
We are using your product nRF51x22_QFN48 with a balun BALF-NRF01E3 from ST and the PA.11 antenna from Taoglas Ltd.
Do you already have this product certified for RED...
Hi guys,
We have noticed some unexpected behavior of supervision timeout in case of few fast sequential calls of connect and disconnect commands in nRF connect app with...
hi...
i am using nrf52382 segger 15.2 version , i am facing issues i couldn't able to send the data ,here i am advertising using condition if my condition satisfied start...
Hello,
I use SDK15.2, SES4.12 and custom board with nRF52840.
I have a strip of ws2812b LED's connected to my device. I've made a simple RGB animation, each frame of which...
Hi,
I've been testing the sample code at_clent with Verizon wireless. I can send AT command to the DK via nRF Connect "LTE Link Monitor".
Q1. run AT%XCBAND=? to print...
Hi ,
I found nRF24LU1+ build in AES co-processor, but I cannot found the processing speed (the time for finish one AES processing) on datasheet.
Because my customer...
