I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
SDK 15.2 API6.1
I am using the ble_app_blinky and ble_app_blinky_c examples and when i connect I see the "Nordic LED Button Service" and inside that i see 2 chracteristics...
Hello all,
In order to optimize my power design, I want to power my sensors though GPIO pin on nrf52832 and toggle the pin when I need to use them.
I have two sensors...
Hi.
I have an experience that I do not understand.
<main>
<timer handler>
"PushSwitch" changed to true when the button was pressed using a switch interrupt...
Dear nordic,
I have a custom board. first time its working fine and i flash the program without any issue. after few days i started to reflash the chip its show some errors...
Hi,
From last couple of months I'm working on NRF52840 chip and designed a battery operated device. I also made 5 prototype boards and I'm happy with the range test, coded...
I see two different issue from Segger ES. The below piece of code work well in debug mode, comparison of array at 2k and it fails at release mode. Wondering what's happening...
As a brief introduction, our research group uses bluetooth advertising to broadcast commands and responses between end devices and 'routers' which are connected to a PC. ...
Hi,
BLE Application on nRF52840 (pca10056) development board is being developed.
Application stopped the advertising to make device non-discoverable.
After that trying...
SDK 15.2, API 6.1
I have 1 firmware and 2 PCB it operates. PCB A was an external crystal and the sdk_config file is setup for the operation. However, PCB B uses internal...
I would like to communicate with and existing product that has the ability to communicate thanks to a UART-Bluetooth module. This module uses a Serial Port Profile and shows...
Hi,
I'm working on a thread network and I have some difficulties to configure the BorderRouter.
I use the BorderRouter V2 rapsberry image from Nordic, I recompile the...
Hi,
I want to be able to update the bootloader along with the application via OTA DFU. I know I can't generate both the application and bootloader in one image/zip so I...
I am looking for specs for the input impedance of the comparators (COMP and LPCOMP) for the nRF52832. I searched the forum and all I found was someone saying it is ">1 Mohm...
Hi,
I am trying to incorporate flash storage library to ble_app_uart_c example. I have added all necessary functions from ...\examples\peripheral\flash_fstorage.
When...
