Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi i am using nRF52832 with SDK v14.0.0 on LINUX, so usually a service and a characteristic have the same name space but you just change a few bytes for every id. But the...
Hi there,
I am having issues to run my program after a MTU increase size.
I am getting the following error:
I am not sure if it is related to the RAM size values...
How to select endpoint transfer type in hid keyboard example?
I am using nRF5 v15 with a nRF52832 and Soft Device s132 and the reports keep being sent as a bulk transfer...
I'm finding my PCA10056 nRF52840 Q1AAAA development kit to be acting very strangely.
1) I takes almost 3x as long to program as a PCA10040
2) Generally I have to program...
I'm using nRF24L01+ since some time, the version on board with LNA end PA with very good results. The electronic is shielded on that module.
Very rarely it happens that...
Hi,
here is the situation:
Compiler: VS 2017
CMake: 3.12
boost: 1.67.0
pc-ble-driver branch: master
Firstly I can successfully build the pc-ble-driver, with this...
So I came from the arduino world and made my life simple by making a resitor bridge with buttons so that I could spare many pins for other features. I have problems finding...
I'm trying to understand which part of the code provides the bluetooth connection between two nRF52840. I worked in sdk15.0.0 with multilink, blinky and uart examples to solve...
Hi, everyone,
We are developing project with nRF52832 chip.
For making it's monitoring we used UART communication port. But on the next step of development we had to enable...
I need to interface an nRF52832 with ADS7042, hence the following questions:
1) as ADS7042 requires 14 clock cycles per read cycle, is the nRF52832 SPI API applicable in...
I am constantly receiving an NRF_FAULT_ID_SD_ASSERT error within a non-deterministic time after connecting via BLE.
The program Counter is always 75936 and Info == 0. I...
Hi
Development Environment : windows 7- keil ARM SDK 5 - Arm Debugger Programmer(Waveshare) - nRF51822 EVK from Waveshare
What is the boot_PIN or Boot_Mode PIN
I want...
I am wanting to increase the length of one of my characteristics used when my device is acting as a peripheral. When I increase the size of my characteristic, the softdevice...
Hi,
I needed some figure for my controller selection,
Please if can you tell tthe exact answer it will be very help full,
Using NRF serial example for uart with baud...
