I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi
I am running SD 132 2.0.1 on nrf52832 rev 1 and i am getting a chip lock reset occurring. (I have cleared the flags as per the errata and reset pin flag is not present...
....\R2D2_build\R2D2_Firmware.hex: Error: Q0122E: Could not open file '....\R2D2_build\R2D2_Firmware.axf': No such file or directory
keil gave me that error. i did research...
Hi
When I used ANCS, there is "bluetooth pairing request" notice shown on the iphone, if choose cancel, then 51822 went to reset, why is that happen?
iOS:10.3.3
NRF51822...
nrf5_SDK 12.3.0
nrf52832
softdevice 3.1
My app used timer for buzzer and led.
This timer call itself, and variable is discount.
This is normal mostly, but in somtimes...
I am working on reading ADXL362 through SPI on PCA10040.I used demo spi in nRF5_SDK_13.1.0.
here is my main code:
bsp_board_leds_init();
APP_ERROR_CHECK(NRF_LOG_INIT...
I am developing on the nRF52 boards with a capacitive sensor. I followed the tutorial in this link and created a custom service with 3 read characteristics. I am able to use...
NRF52 pca10028 DK - SDK14 - Arm GCC (Eclipse) - SD 5.0.0 - bootloader_secure_ble
Using either nRFGo Studio or eclipse to program the flash (it does it with both)
I can...
Hi,
some time ago we ordered 3 PPKs. I tried one under a Mac with VmWare / Win7 with a PCA10040 board. It was working but I got surprising graphics. When I came back from...
Hello,
I am just using the SDK13 on the nRF52832 together with the experimental BDS example (I modified it to the point where it seems to be working fine so far).
Now...
The following does not allow me to define NRF_DFU_HW_VERSION in my makefile, I get redefine errors due to this broken if else in def_req_handling.c:
#if defined (NRF51...
I want to evaluate the nRF52 SDK , but don't get how to install it.
The Getting Started section mentions an MDK installer. However, I cannot find any such installer inside...
Using the nina 112 with nrf52832 SDK 13
I have got a problem with the I2S Interface.
I configured the RESET Pin as normal PIN. Tested with GPIO as Output it worked. If im...
Can we build the FW manually and upload to the Thingy via the OTA uploader? We built the FW, created the DFU, and inserted the .zip file in the iOS app, however get an Error...
Hello!
I am working on a project. The goal is to retrieve every seconds some acceleration data from the ADXL362 accelerometer.
I configured the spi in blocking mode...
Am i right in thinking that if GPREGRET has not been set then we can not guarantee what value it will be?
I.e on power up we can not guarantee that its value is 0.
