I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
We are having an issue with
This happens to us because we are using the NRF carrier library, and in the carrier library, when you are trying to power off the modem,...
Hi, I'm coding a nrf55832, my code uses TWI, UART, SPI, app_timer, nrf_drv_timer. The code was going welle until i add the saadc. When i call the nrf_drv_saadc_init function...
Dear Nordic Engineers
I used gd25lq32e to replace mx25r6435 and it is a 32Mbit Flash, when I add it to the Devicetree of Lwmwm(NCS 2.6.1), the build will report the following...
I'm currently working on a POC for the nRF9160 with an external host processor. I have the Serial LTE Modem example running on the nRF9160 and have the serial comms between...
Hi,
I have a simple question ... I think.
I have been limiting my USBD reads/writes to 64 bytes as NRFX_USBD_EPSIZE and NRF_DRV_USBD_EPSIZE are set to 64 bytes. I have...
Hi all,
I am using the nRF5340 DK. I am trying to run the ncs/nrf/samples/openthread/cli sample with no changes. I have tested this in both ncs v2.7.0 and v2.6.2. I am able...
I'm adapting the sample code for TF-M secure peripheral sample (NCS v2.5.0, nrf/samples/tfm/tfm_secure_peripheral ) to also add a UART peripheral. But this sample uses the...
If there are any compile errors in a LOG_xxx call, the compiler prints so many error messages that it becomes impossible to tell which is the actual error. E.g. below is the...
I've just purchased a PPK2 and before I did I check to see if OS X 11.7 is supported - it is ( https://docs.nordicsemi.com/bundle/nrf-connect-desktop/page/os_support.html...
Is it safe to connect the communication peripherals (SPI, UART, I2C, etc.) of an nRF52840 in system_off state to powered peripherals that might (or not) possibly transmit...
Hello Nordic Team ,
This is not a technical problem/question. I don't know this is correct place to write but I want to inform Nordic and whole community in Turkey. I am...
We are working on a broadcast assistant that should be co-located with a broadcast source, and it should only help with the stream provided by this broadcast source.
What...
Hello,
I'm designing a custom board with an nRF52840. I currently have an nRF52840 DK (PCA10056, v3.0.1) and would like to use the on-board debug out header (P19) to program...
Hello,
how can I increase the number of ZBOSS buffer (zboss_api_buf.h)? Currently they are 25.
We are using nrf52840 with nrf5 sdk for thread and Zigbee v4.2.0 without...
