I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
as soon as I include CONFIG_REQUIRES_FULL_LIBCPP=y in my prj.conf I get an error "undefined reference to `_impure_ptr'" when building:
This happens when I try...
When I developing application with nrf SDK,I can set device name by sd_ble_gap_device_name_set().
But when I turn to NCS,I should set device name such as CONFIG_BT_DEVICE_NAME...
Hello everyone I am using Nrf5340 Zephyr sdk v2.4.2 to broadcast BLE as a peripheral connecting 2 devices with Esp32 as central and phone at the same time, the following error...
Hello,
Does anybody know why I can not discover the service uuid as shown in the picture below?
I want to connect a sensor with this chip nRF52832, it's service UUID is...
Hello,
I'm using nrf52840 USB Audio headset application on nRF52840 DK. The nRF connect SDK version is v2.6.0.
I want to change the output to i2s out. The following are...
Hello, I have a few questions about sending code via J-Link. We are doing our project on vscode with 2.6 sdk. When working with nrf5340dk, flash via vscode was enough. However...
Dear lovely people from Nordic Seminconductor,
I have the nRF52840 dongle.
I installed the software ""nRF Connect for Desktop" on my Ubuntu 24.04
For that I ensured...
Hello,
I am using the NRF52840 dongle, and for my project I need to be able to send/receive data from a RaspberryPi and also send/receive large strings between multiple...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I want to use Emulated RTC driver functionality.
Therefore, I configured prj.conf file as (based on This Link ): CONFIG_RTC...
Good afternoon,
For a beamforming application in the Wi-Fi range, I am planning on using an nRF24L01 to generate the signal.
The signal would later be split into N different...
Hello,
So I have an IO Shield with the nRF5340 SoC. I have connected the IO Shield to the Port 12 of the nRF5340 Audio DK as shown in the schematic:
Connections:
Debugging...
Hi,
I am trying to sniff between my phone and a BLE device.
When I put the device in pairing mode, I can see it in the "advertising" list. Then I select it (but I don...
Hello Nordic Forum, I am working on a project involving data transmission from an nRF52840 board to an Android application, and I would appreciate guidance and insights from...
Hi.
There is MainThread and MeasureThread.
There are also two events that MainThread sends - BIT(0), BIT(1). These are Start and Stop.
In MeasureThread, we first wait...
