Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I am looking into the example of SAADC and sending data through BLE. My tests are based on this example: github.com/.../ble_app_uart__saadc_timer_driven__scan_mode...
Hello,
I have been working on a project that uses nrf52832 custom board. Recently, I have been trying to implement device bonding and realized that the data transfer rate...
Hello All,
Hoping this one is an easy one - have an image for the nRF9160-DK - it hangs unless I make a serial port connection - so, apparently - printk() is blocking waiting...
I like to use nRF52840 now instead of nRF82833 which was used during the CE-RED compliance test. I only like to change the nRF chip. All other components at the PCB will stay...
Hi Nordic support,
I'm sort of new to Nordic development..
1. Is it possible to output 32.768 KHz clock on a GPIO of nrf52 device ? In our design we use two crystal oscillators...
Hello,
We are developing an application using nrf52832 and the ncs 1.8.0.
Since our solution is battery operated we have configures application to sleep by default and...
Hi, I try to understand how to use the k_thread_create() to spawn a function (here called spam()) that takes a argument, and then runs with the argument. This code will not...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
Here I am trying on transmit a...
Hi everyone!
I am working on a project where I have to store files inside a FLASH coming from a GATT server , and be able to manage them through FAT in a GATT client . The...
hi professor,
software:nrf connect SDK 1.9.1
hardware:nrf5340
I have merged the peripheral_uart project to peripheral project.When the uart receive data, the asert...
From the introduction video it was stated that the Thingy 53 has a 4-pin JST connector which includes I2C. But there don't seem to be any documentation about this connection...
Hi,
I have just updated to nRF v3.11.1 on my Mac and "Toolchain Manager" is now failing to load, all the other apps seem to run correctly.
I have restarted the app...
Hi,
We are currently filling out the forms for BQB certification and I have some questions. We are using S132 v7.2.0 and NRF52833 for which I have already seen at infocenter...
