I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I have the sparkfun NRF9160 thing plus, and using the NRF Connect SDK v1.8.0 in visual studio code I can load programs like Blinky and hello world and everything works great...
I have been working and studying how zigbee protocol works, I start with coordinator, light bulb and light switch. it was fun example. However now I want to send the reading...
hi,
When I add the program inside the hrs saadc is found fatal error, DEBUG found the program stopped here
SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL);
error_code =...
Hi
I am having some issues with running QSPI on the nRF5340DK board. After I disabled the QSPI, I found the board still having a high current consumption of 700 uA.
Although...
Hello,
We use SEGGER_RTT_ReadNoLock() in our code, and this works perfectly. Our nRF is connected to a DK, which is connected to a computer.
However, when we compile with...
Good Saturday evening,
Up until now I’ve been accessing the registers directly in my Nano 33 BLEs to experiment with Timers, GPIOTE and PPI, all via the Arduino development...
Hello,
We're building zigbee devices around the nRF5340 with the nRF SDK/zboss/zephyr. I'm working on custom boards and have based my 802154 code around the samples in nrf...
is there a way to get more control over the auto ack feature of the 802.15.4 driver in zephyr?
I would like to ack frames without destination address only if nrf_802154_ack_data_pending_bit_should_be_set...
Hi all:
I have a software version that allows Bluetooth to be connected to the phone normally,
When I tried to use the SPI interface, it happened as long as I used
...
Hi there,
I'm trying to wire up a Uarte client to a Uarte server where the client device is an nRF9160DK, and the server is an nRF52840DK.
Connectivity between the cilent...
Hello,
My hardware guy asked me to look into whether or not we can use a fixed eSim (no card) with the 9160? If this is possible how do we program it with the particular...
Hi,
GOAL : I try to measure the current consumption in system off only.
PROBLEM : I measure a current of 8uA in system off while in the datasheet of the PAN1781 et nrf52820...
Hi, I accidentally marked one of my own replies as the answer.
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple...
Hello,
I am looking for an example that have the the ccs811 on the sdk15 but i didnt find it , I have found some driver ext like ccs811.h on the driver_ext file but I dont...
