I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I have a question about the maximum number of characteristics. I searched DevZone for the same question...
Hello!
I've just updated from v3.7.0 to v3.8.0.
Devices discovering seems to not operate. (two nRF52840 dongles are plugged in).
Programmer 2.0.0 output looks like...
Dear Ladies and Gentlemen,
I am trying to get a DPS310 pressure sensor to work via SPI. As I use I2C for other purposes, I chose SPI1 channel. The given SPI example in SDK...
Hi，I am trying to use nrf52832 to drive the ad5940 chip, but using the function in the SPIM driver library to initialize the ad5940, I have been unable to get the ID of the...
Hi Nordic,
i'm using a nRF51822 based board (Adafruit Bluefruit LE Sniffer, PRODUCT ID: 2269, https://www.adafruit.com/product/2269 ) and could sucessfully update to nRF...
Hi
Sorry,This case is the following of case ID: 278538, I didn't find a reply button option in case ID: 278538,So I recreate a new case, I failed to create a new application...
Hi. I am trying to get the gsm modem sample project to work with an nRF 5340 app and a Nimbelink LTE modem, NL-SW-LTE-TC4NAG. The only change I made to the project was to...
Hi Nordic Support Team,
First sorry for basic questions.
I'm learning the basic hardware setup & Linux driver configuration things to setup & configure the MCU(i.mx6)...
Hi, i am Agustin.
I am working with Thingy 91. I am using the Asset Tracker V2 application to upload data to AWS. I have a problem with "Build Solution".
Hi , I got a problem when testing nrf53 qspi signal using a logic analyzer ,with a non-blocking init of qspi and a 4 Byte write , codes are below:
I got a word align problem...
Hi Team,
I want to use the Nrf52840-CAKK-R7 chip to fabricate a PCB board. And communicates with other chips by SPI interfaces.
Now, I want to select the GPIO ports by...
Hi All,
I'm using nRF9160DK PCA10090 Version 0.9.0 and I want to update the Cellular Modem Firmware using nRFConnect 3.8.0 Programmer v2.0.0. Debug Probe is switched to...
We have a timer with a number of variably sized intervals as illustrated below operating on a single capture/compare channel (CC):
Currently the method we use to set the...
Dear all,
In the datasheet and online it is mentioned that the DAP (Debug Access Port) is activated when a programmer is attached. Moreover, it can happen that the programmer...
