I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi, when i'm debugging my circuit, the logical of a if or while don't work. In the image, the timeout_rtc is higher than 100, but the value of a don't change to 1. What's...
I used the P1.13 pin of NRF52833 as the output pin, and used it in the manner of the blinky sample program, but it crashed and prompted the following error message:
***...
Hello, I have a custom HOST board. There are use NRF52840 BLE chip.
I'm run Bluez 5.61 on the HOST board and by meshctl> I am able to run as a controller. But if I want...
how to set BLE_GAP_ADDR_TYPE_ANONYMOUS
i have follwoed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners...
Hi,
There are tons of documentation on how to make a mouse, keyboard or remote control work as a HOGP device, and I have successfully implemented both mouse and remote control...
Hi,
Using NRF Connect 1.6.1 on NRF5340 I have modified hci_rpmsg project to add another endpoint for bidirectional calling between app core and net core. I have used the...
Is there a reason that AT_CLIENT example always works for LTE but SERIAL_LTE_MODEM only works the first time, and then trying again it never connects to the LTE ? Typing AT...
I’m trying to write a program that reads data from 4 hall effect sensors and outputs it to a serial monitor over Bluetooth. The sensors communicate over I2C. The programs...
Hello,
I've purchased the nRF52840 Dongle: https://www.nordicsemi.com/Products/Development-hardware/nRF52840-Dongle . I've successfully flashed it with the version 4.0...
Hi：
I use nrf52832 to connect to the sensor module through uart. When the sensor device is turned off, I can repeat the pairing and unpairing of the Ble module through the...
Hello,
After reading many things, I would like someone to confirm or correct my understanding. I believe this will be great clarity for others as well.
The nrf52 requires...
Hello dear all. I am compiling a firmware to merge the timer function into the nrf52-ble-app-uart-c-multilink firmware. The timer function is copied from ble_app_uart__saadc_timer_driven__scan_mode...
Hi,
I am a new beginner when it comes to Thread and Matter. I am trying to run Matter on nrf52840. I flashed the door lock example, commissioned the device using BLE and...
I am using SEGGER Embedded Studio and an nRF52-SDK circuit board to run example ble_central\ble_app_hrs_c from nRF5_SDK_17.0.2. I have a peripheral that reports motions. The...
Hello Nordic, We are preparing for mass production with nRF9160. We have a script to flash, register the thing on AWS and write credentials on the modem using nrfjprog. We...
