I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
hiii,
I'm using the light switch example from the mesh SDK, version 5.0. I've successfully configured the client and the server using the nrf mesh app. however, my client...
When I do a 'build and run' in Segger Embedded Studio I get this error
Then I press the reset button and everything works.
If I do 'build and run' again the error repeats...
Hi
I would like to add to the scan_adv example, the possibility of the FOTA upgrade.
I can merge the scan_adv and smp_svr examples, and get them to work at the same time...
Excuse me:
1、The customer wants to use p0.21 pin as General purpose I/O，Can the reset circuit of p0.21 pin be removed？
2、The customer said that when a new nrf52832 chip...
Hi,
I want to add DFU over mesh and usbd into the client example.
I have faced an error of Multiple definitions of UARTE0_UART0_IRQHandler. I comment out the UARTE0_UART0_IRQHandler...
Hello,
i am currently trying to create a project that uses the NRF52840 board as a switch to control sylvania smart+ A19 filament light bulb.
However, i am unable to detect...
Hi,
I'm using NRF52840 in order to implement an application which will connect to a mobile device with PIN code (MITM). In addition - my app will be able to connect to a...
Hi everyone,
I'm using the nRF5340 board, nRF Connect SDK v1.5.0 and the nRF Connect app.
I am also using the example code "beacon" and all the data with integer format...
Hello,
I have been developing a serial C# application to work with the nrf52840 chip, initial development was done using the nrf52840 development kit which worked without...
Good morning,
I am using SDK 16.0.0 and nRF52832 uC. I have a project where I need to connect the uC to a CoAP IP. The only internet access it has is through an SoC developed...
Hi, Usually we set FLASH_START macro to indicate application start address, I do like to consult is't possible to change the FLASH_START from prebuild binary file without...
Excuse me:
PCA10095 cannot be download .hex on SES and nrf conncet programer,The figure below shows the problem downloaded on SES.How to solve tihis problem？
Hi, dear Nordic & all：
When I run libuarte example，I found a problem， I just set P0.14 to high at the begin of mian function, then I send data and test the example's function...
