I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I am seeing very little information. The LTE button lights green but Modem and UICC stay red. I get signal strength but none of the other items in the block; they are all...
I m using The nRF52840 + STM32 with serialization library. My device is set in central mode and i want to active whitelist,
the configuration seems to be applied correctly...
Dear support,
Anomaly 89 of the NRF52832 states that a high static current consumption is observed when the SPIM/TWIM uses EasyDMA and the GPIOTE is configured in event...
Hi, all
I'm using nrf52833, pca10100.
I merge nrf5-calendar-example to my project just like this.. ( I've only tried initializing.)
and error occur in nrf_sdh_enable_request...
I am interfacing the nrf2832 with the sim 808 module.
In order to be able to send a message I need to use Ctrl+z.
This should be entered as an escape sequence.
I have...
Hello
When we evaluated nrf52833 (using DTM), everything was normal at 1M, 2M, LR. However, during CTE evaluation, after the serial port sends a configuration command, the...
Hi,
I'm on SDK 17.0.2 and SD 340. Trying to combine BLE services as Central server with BLE HRS_C example. The idea is to read the BLE HRM and also to be able to connect...
Hello,
I am trying to enable RTT instead of the default UART output of the nrf91dk AT client code example. I am using Segger Embedded Studio V5.34 with Nordic nRF Connect...
when using nRF5 SDK Release 1.4.99 the the projects open some have errors that prevent it from building for the nRF5340,
when I attempted to use nRF5 SDK 1.5.0 or 1.5.1...
Hello, everyone,
I got a Thingy91 and I would have liked to be able to measure the current that passes through the NB-IoT modem, for that, I followed this tutorial :
https...
Hi dev team,
I am using a Thingy91 device along with the NCS v1.5.1.
I used the AWS FOTA example for firmware upgrades and I integrated the example in my code.
The FOTA...
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of openThread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure...
Hi Nordic Dev Team,
I am trying to send my log data from my flash memory into Android Phone. I followed this example :
github.com/.../nRF5x-custom-ble-service-tutorial...
Hi,
Setup:
DK : nRF-52840 PCA 10056
IDE
SDK : nRF5_SDK_17.0.2_d674dde
Coding Language : C
Please find 5 queries listed below.
1) My plan is to automate BLE...
In a .c file ,code like below (build a image using nrf5340dk_cpuappns) :
#include "nrf_gpio.h"
#define SPIM2_CS NRF_GPIO_ PIN_MAP(0,15) #define SPIM2_SDO NRF_GPIO_ PIN_MAP...
