I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi
I'm trying to use Crypto but can't get started because micro-ecc isn't installed
The install instructions say:
Enter the subdirectory for the SoC and the toolchain...
I have been trying to bring up a secure boot loader for our product based on the nRF52832 SoC.
I have reviewed three SDK versions (17.0.2, 16.0.0, 15.3.0) and observe the...
Hi,
I know that the QSPI peripheral of nRF5340 allows to augment memory by interfacing an external SPI Flash memory. In addition to the internal memory, does DFU by FOTA...
I use nrf52840 dongle on windows 10 to connect to ble devices, I can connect and send msg to the ble device ,but I tried "att_res, data = self.adapter.read_req(new_conn,BLEUUID...
Hello Everyone,
I'm looking for an MCU that could be used as a master for SPI communication to supply the necessary signals (CS+, SCLK+, MOSI+) to a slave device (amplifier...
Hello,
I have migrated my codebase from v1.3.0 to v1.4.0 of the nRF SDK and have a strange issue now where the serial port is spitting out sleep debugging information in...
Hi,
The nrf52832 product spec shows all the clocks provided by HFCLK and LFCLK. But where can I find which peripheral is using which peripheral clock specifically?
For...
Hi,
I need to read some BLE characteristics presented by a commercial device nRF52-based, using my nRF52-DK, based on the nRF52832 and PCA10040. I don't have the firmware...
Hello experts,
I would like to get my mind clear on this.
I am using NRF52833 for our custom board we are using Zephyr RTOS (NCS v1.4.99) and IDE is segger embedded...
We need to accurately control the time when the Bluetooth advertising package is sent out, so that the two slavers can simultaneously send the beacon data to produce the signal...
Hi,
I am facing an issue when setting up advertising intervals (in connectable mode).
Whatever the value I enter I will always end up with an advertising interval of...
Hi,
I am currently working on the ble mesh project. I would like to know whether there is any cybersecurity related examples in SDK .
1. Can you list out some of the security...
Hi,
So there is a dataflash MX25R6435F available on nRF9160 DK.
My question is that is it available for general purpose? If yes then how can it be accessed?
Unfortunately...
I am trying to use the PCA10059 dongle as the connectivity device with pc-ble-driver-py
The script I am using works with a PCA10056 devkit loaded with the connectivity firmware...
I now integrate USB, BLE, LLPM, keyboard HID and Mouse HID to nrf52833.
When I added CONFIG_DESKTOP_HID_MOUSE=y, my project was abnormal.
BLE connection: Move Mouse and...
