I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
hi
i have added a timer to a working code with softdevice, ble, uart and pwm for now.
when program starts it gets an error in the app_timer_init funcion ' NRF_LOG_INFO...
Trying to port some SPI code to the Release 15 NRFX API and seeing an error from nrfx_spi.h, line 82
/** @brief Macro for creating an instance of the SPI master driver...
Hi,
Could you confirm that DeviceID found in FICR of nRF9160 is:
1/ randomly generated (64 bits = 8 bytes)
2/ they are not unique, but already on the chip when it...
Hi,
Greetings!
We have successfully checked DFU application from SDK16.0.0 and it works nicely.
We have used android nRF connect app for firmware updating.
Here we...
We have been supplied with a module that sends SpO2 data but it uses 8bit, plus odd parity. I have seen the many questions on this subject and only pose this question to add...
To be able to have USB communication/interface, do I need to apply 5V to VBUS? Or will 3V on Vdd be enough. I am planning to use coin cell that is max rated for 4.2V so it...
this is my code on DFU function, I copy to the example of experimental_ble_app_buttonless_dfu on SDK12.1. I used nrfgo studio to program s130_nrf51_2.0.1_softdevice , boot_setting...
Hi,
I've been working on Thingy:91 under ncs tag 1.2.0, trying to develop simple application using NVS just to see how it works. Based on the zephyr sample I wrote the following...
Hi:
i have some problem about using ble.
in my application has a loop:
1.use ble adv,and Wait for a while，
2.close ble adv ,and using base radio funciton.(do stop...
Hi
I was able to successfully complete the RF output power measurement using nRF52840 DK with the help of Nordic devzone last time.
Based on successful measurement...
Hi,
I use proprietary service to transmit data between raspberry pi and nRF52840 DK. The example I referred to is below.
C:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral...
On the nRF52840, I know the PPI, and therefore any events/tasks, are synchronized to the 16MHz peripheral clock. Here is the quote from the documentation:
"On each PPI channel...
