Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hai, i try to MFRC522 rfid reader interface the nrf52833. 1. I try the read version from reader but it's only show the 0xFF 2.I try to read the card id . it is not work. I...
I'm unable to import/export mesh networks and then subsequently send mesh messages. I believe this problem has been mentioned before [ 1 ][2][3], but the solutions offered...
Hi,
We've had a mesh sensor network all working for a long time using SDK17.0.2 + Mesh SDK 4.1.0
The data is accessed by a mobile app through a mesh node acting as a proxy...
Hey
I am struggeling to build the smp_server sample for the nRF5340:
west build -p -b nrf5340dk/nrf5340/cpuapp/ns -- -DFILE_SUFFIX="nrf5340_bt"
fails with a linker error...
Hi Nordic Team,
I’m currently using two standard nRF5340 DKs (non-Audio DK) running the nrf5340_audio application.
We’ve successfully adapted I²S speaker output on unicast...
Hello, I am going to use nRF52833 to develop a remote controller based on Zigbee RF4CE specification.
From the nRF5 SDK for Thread and Zigbee, it looks like RF4CE should...
Hello,
Is there a way to change the LPCOMP reference level in Zephyr other than what is set in the devicetree overlay?
I'm happy to disable it, change it and re-enable...
I am experimenting with the Nordic ESL sample application. The central_esl app is running on a nRF5340DK. I would like to add the nRF21540EK to this to improve the range....
I'm suddenly getting this error message with nRF Connect for Desktop. I've tried deleting and reinstalling, but the same error persists.
What should I do?
Error: Failed...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi everyone,
I'm trying to interface the nrf5340 with the intan chip rhd2132, that allows to record signals. I can read successfuly the registers, but when I try the recording...
Hello,
We are using nRF54LM20A and NCS3.1.1 for our current product development.
we were using PDK/DK for our development and we got the datasheet "nRF54LM20A_Preliminary_Datasheet_v0...
Hello everyone!
I'm trying to get a custom board based on the nRF54L10 working. I am currently connecting it to my computer via a J-Link Edu and would like to get some basic...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
How can I confirm that an nRF52840-based device has been successfully provisioned? I don’t have physical access to the device, and it is running firmware that performs self...
