we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi there:
I were develop product with nrf52832 ,nRF5 SDK version 17.0.2 and mesh sdk 5.0.0. And i install the toolchain on the ubuntu 20 follow the guidance https://infocenter...
Hi Nordic,
I am working with nRF52840, sdk17.1.0 and got a pcb with external flash with GD25Q16E.
Pins usage are: SCLK: P0.25, CS:P1.00, SIO0:P0.21, SIO1:P0.15, SIO2:P0...
Hello everyone,
I am developing a product with nRF52840. The board has a magnetic sensor (LIS3MDL), a ToF sensor and a LoRa module (Sx126x).
I have worked with nRF52 products...
Hello all!
I would like to use the PWM driver, yes, the hardware that is on board the chip. To get going certain code parts from the PWM driver that comes with the SDK,...
Hi there,
We are using the Serial LTE Modem MQTT client .
So when the #XMQTTEVT messages comes in, the first parameter <evt_type>, is documented well here:
However...
Hello.
I want to write 3 bytes of data using BLE in a memory area that will not disappear when the nRF52820 is powered off or reset.
Currently, when I create a program...
Hi, I trying to run the spi_flash example form zephyr.
My sdk in 1.9.1 - nrf52840 in a custom board.
I have tried everything and I always get the same result:
JEDEC...
Hello,
Aim : To write and read x bytes from the QSPI interfaced external PSRAM(APS6404L-3SQR) using the nRf52840.
Configuration : Following is the configuration of the...
Dear support
I am developing a generic central application intended to connect any BLE devices which is connectable. So I need to figure out which parameters are needed...
hello Nordic
i am working with nrf52832, ncs 1.7.1
we have to turn on the power before trying to read jedec and to avooide changing ncs spi_nor or using SYS_INIT we decided...
Dear Nordic-Support Team,
Introduction
I have read through some sources (tickets and documentation) but I am still struggling to see the big picture of UART configuration...
SoftDevice: S113 v7.0.1
SDK: 15
Chip: nRF52840
It looks like setting PA/LNA pins on port 1 result in NRF_ERROR_INVALID_PARAM being returned by sd_ble_opt_set(). When...
Hi All,
We have been using NRF52 products for a few years now and currently doing an PoC of using the BLE DFU with a CODED_PHY.
Our solution does use the DFU already but...
I am using the nrf_serial library SDK 15.2.0. I have implemented the solution suggested in Case ID: 216973 for recovering from driver errors. This helped me get over errors...
