I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hi,
I'm trying to send and receive scan request/scan response. The system consists of 2 nrf52840, 1 central and 1 peripheral. They both advertise and scan on 1M and coded...
I'm currently working on a program that automates the Legacy DFU procedure and I'm running into some strange issues with writing to the DFU characteristics.
On the nRF Connect...
Hello,
I am trying to use the FDS module with the Softdevices and Peer manager.
I can store some data and I am able to read the header of the record, but when I try to...
Hi,
I want to use the static version of pc-ble-driver in my c++ code. I am learning cmake but I have no expereince with Ninja. I'm using only the version 6 of the API. My...
Target application 1: Data acquisition is carried out for a 0-1khz high-low level signal. The low level is effective. The count is increased by 1 for each trigger. 2: Use...
Excuse me:
I'm developing a keyboard with nrf52832，Calling ble_hids_inp_rep_send() returns BLE_ERROR_GATTS_SYS_ATTR_MISSING when the keyboard is just connected to ipad4...
Hello All,
I am developing a prototype for one of my application.
I am trying to integrate the zigbee stack to my base firmware.
For my application I am using RTC2....
Hi,
I'm using the example "ble_central/ble_app_uart_c" of nRF5_SDK_17.0.2. Connection to peripheral workes fine.
If the central re-starts while a connection is established...
Hello, there
We made a custom tracker device with nRF9160. During prolonged use, we observed that k_delayed_work_submit_to_queue sometime return -22 and cannot be recovered...
When i change the config NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS to 1
the following error comes, how do I overcome this?
<debug> app: nrf_dfu_svci_vector_table_set() ->...
Hello All,
I am facing binding error if I use UART1 for binding but UART0 is working fine. Refer the below error.
Please let me know the solution to solve this error....
Hey!
I'm trying to adapt a modified version of the open bootloader example for the nRF52820 MCU and have one issue as well as some questions.
I have adapted the build...
Hi,
I am developing a system consisting of a BLE peripheral and central with a custom service (SDK 17, S140, PCA10056).
For the peripheral, I am using a modified version...
I have noted that the code size of my project is reduced by more than a factor of two if I set NRF_LOG_ENABLED to 0. It is also reduced significantly if I set the Log Level...
Hi
I would like a clarification when performing DFU from external flash. This is applicable to both nRF52 and nRF91, I guess, as long as nRF Connect SDK and MCUboot is used...
