Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I'm developing for nRF52 DK
using SDK 17.02
Segger 5.10b
I'm developing a service to read pin 12 where I'll have a square wave signal of about 60Hz. When I tested my...
Hi,
Is there an example code for nRF52832 were the system is configured to operate in a certain duty cycle, e.g. performing a certain task once every 100ms, and then goes...
Hello, guys.
We want to use libuarte - advanced UARTE driver in our current application developed for nRF52840 with SDK 17.0.2.
We can successfully run libuarte example...
I'm using nRF52 DK (PCA10040) <TWI sensor> example.
On line 139, printed result = NRF_SUCCESS
However, the program doesn't print line 142. Instead, the code jumps to twi_handler...
Hi, we just found out a bug in nRF Connect for Android indicates that the phone Sony Xperia L4 supports Coded PHY. Unfortunately, when we try to run Bluetooth: Central Heart...
Hi,
I am currently trying to run the secure_bootloader example given the in the sdk 15.2.0. I am currently having trouble as when I try to send the file, the error shown...
hello Nordic
i am working on nrf52840, SDK16.0 developing on the peripheral app_ble_blinky example.
i am use a pin as input interrupt from other device,
if i does...
Hi,
My application uses the nrf9160dk and I program 3 Zephyr images onto the 52840: (1) bootloader, (2) image1 and (3) image2. There is no SD or anything else on the device...
Hi, I have a holyiot NRF52840 dongle (schematic below). I am able to program it via the swd interface and have BLE examples running (as long as power is attached to VDD),...
I have an application that is running the following setup as a multi-connection (peripheral and central) setup:
I am having an issue when a peripheral (NUS) is sending...
Hello everyone,
I am going to run the mesh DFU example. I found that I must use Python2, not 3 to work correctly. I follow the instruction suggested in this post.
https...
Hello, i don't know how build many project with other configuration. I want to do a lot of configurations.Then for each of them make hex files with one click of a button....
Hi
When I try to build NCS sample using SES (v5.40, also v5.30a nordic edition) it seems to build the project correctly (.elf, hex are generated) But it throws error at...
I am trying to bring up an application that uses the soft device, but not right after power up.
I want to use an application timer to schedule a timeout say 10 minutes after...
