After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
I note with interest that Nordic is providing support (e.g., downloads) to run CircuitPython 10.1.4 on various Nordic devices, including the nRF54H20-DK . I've just received...
Hi I am able to load the nrf9151dk_at_client example hex on my custom dev board . I try accessing the AT commands and I can very easily get the responses. I want to install...
I'm using nRF52832 SoC with nRF5_SDK17.1.0 and SoftDevice v7.3.0. I'm using following code to write data into flash.
err_code = nrf_fstorage_write(&g_fs, write_addr, buffer32...
HI，
I am currently conducting secondary development based on the periodic_adv_conn sample in the ncs 3.2.1 SDK . Now I want to add continuous carrier wave output and continuous...
I work on nrf connect sdk v3.2.4(nRF54L15).
I plan to run the main application on cpuapp and the device control application on FLPR. It's currently working fine. In the...
I'm currently testing an app, which was running with a nrf9160/mfw-1.3.7/NCS 2.9.2.
Running this app now with nrf9151/mfw-2.0.4/NCS 3.1.0 seems to get a smaller response...
Hi,
I am working on the XIAO BLE SENSE board which has nRF52840 SOC with P25Q16h 2MB flash and other sensors
I want to access the external flash to store sensor data....
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hello,
I am using the nRF54L15-DK development board running the official hci_uart example as the BLE controller. My own Linux system acts as the host using BlueZ to control...
Hi Nordic team,
I noticed that when using the external FEM (nRF21540) with the nRF54L5 device, the power consumption at a transmit power setting of 8 dBm is significantly...
Hi, I have implemented a soft UART in the VPR FLPR. I am having trouble power managing it. I see an unexplained extra 500 uA current draw after I start the CPR until I reset...
Hi, for nRF52840 raw proprietary RADIO mode, do TXADDRESS and RXADDRESSES imply a hard total node-count limit for a custom multi-node network, or only a simultaneous hardware...
SDK is NCS2.9.2,My device supports master-slave integration. As a slave, it can pair and bind with a mobile phone. As a master, it can scan and connect to two slave devices...
HI
I’m doing secondary development based on periodic_sync_conn in NCS 3.2.1 .
After establishing a periodic advertising sync, I have two issues:
Sometimes the buf...
