After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Dear Nordic
hardware:NRF5340, sdk:2.6.1
Our project needs to use floating-point calculations. Attempting to add CONFIG_FPU=y and CONFIG_FPU_SHARING=y to prj.conf will...
I use GNSS with the timout at 0 and interval at 65535.
I do not really need the location but is it nice to have a kind of a log of it because it is available en power consumption...
Context: We are planning to connect the nRF9151 to a private test network using a coax. cable. for development debugging.
(#1) Do your modules support SIM cards with test...
Good day
I have a lwm2m client running on a custom nrf9160 board. I would like to run everything network related to network on a separate chip. Assuming that the two chips...
Some guidance on this query,please. I have a project with several freestanding application (please check topology below). I would like all the apps to acccess a custom board...
Hi,
I am currently configuring the nPM1300-EK with the nRF5340-DK by following the instructions from the webinar "Adding battery charging and fuel gauging to your nRF52...
For a device like the nRF9160 Feather, you need a second USB to UART device for listening to the modem traces. When I go to select the Terminal Serial Port under Advanced...
Hi All,
Im very new to this how firmware space and would love some help.
Currently i have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
1. Hi i am using nrf52840 sdk ver 17.1.0 in secure bootloader /pca10056_uart_debug
2. I have flashed the dfu uart code without any change
3. while performing dfu via uart...
We are developing a ZigBee-based end device using the nRF52840. We have implemented most of the functionalities and also reporting and are able to receive reporting information...
I am working on a wearable which has Fanstel BT40F MCU (SOC nrf 5340). when i initially turn on my pmic, it can only generate 1.8 volt from buck 1 regulator and I am thinking...
Hello!
I have a custom board with an nRF52805 on it and I am simply trying to run the Zephyr blinky example and verify I can see a GPIO toggling as my first step. I installed...
Hello, I'm currently looking for a comprehensive example of DFU-OTA (Device Firmware Update Over-the-Air) using the latest SDK version with the nRF5340 platform. If anyone...
Hello im using Dwm1001C with NRF SDK 14.2 for uwb localization measurements. I have a example project that measures the position of the tag. Inside this project at some places...
