I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
On a custom board we are using an RTC chip to generate the 32khz clock.
I have verified that the hardware register is set to external, bypass, and the src is xtal. The clock...
when i got a nRF5340 DK,
firstly,i use the vscode to open sdk and build ,
secondly,start to run the ncs2.1.2 sample (path:v2.1.2\nrf\samples\bluetooth\peripheral_uart...
I wan't enable approtect by add this line in main.c:
const uint32_t approtect_set __attribute__((used,at(0x10001208))) = 0xFFFFFF00;
but when i compiled at IAR,its show...
Hi, I'm setting up my environment on a new laptop. The project I'm working on requires tflite-micro and before I found that I needed to add tflite-micro to the 'name-allow...
Hai Team,
I am working on NRF52840 based on the BLE Connection handle
Here I am using the ble_app_multilink_central example of SDK
case BLE_GAP_EVT_ADV_REPORT: { uint32_t...
Hello,
I'm following this tutorial to learn how to create a Matter application from template. I did all steps and wanted to build the application. However, the build failed...
Hello,
I'm using the nrf52-quadcopter example from NordicPlayground. After successfully building the project and connecting the MPU6050 , I got a hang during sensor initialization...
Hello,
I had bought 3 sets of Audio DK and had managed to brought up in BIS and CIS mode using the default sample project, however the output is mono output. Can I checked...
I've started to get this error when trying to do a DFU update on nRF Toolbox (v5.0.8): "Can not create Firmware".
The same firmware file worked before on the same device...
Hi. I'm using nrf5340. I confirm internal clock(LFRC RC osc) exist,I want to remove external 32.768kHz X-tal. If yes, how can I turn on LFCLK RC oscillator in my source code...
Hi,
I was successfully able to flash the peripheral_uart code to the dongle and then connect to the Nordic APP.
But it does not connect with the UART when in BLE mode...
I am working on nrf52810. I raised the RAM size in the linker file, which is larger than the real physical RAM capacity, for the testing purposes. I anticipate a hard fault...
Hi:
I use mqtt_ Sample routine: MQTT is connected to the server, and I shut down the server. At this time, the 9160 status has not been updated, but is still connected....
Hi
1、Now we connect the VDD to the battery voltage (3.4-4.2), and the VDD_GPIO is fixed at 3.3V. In order to match the GPIO of other peripheral cpus, will all GPIO be connected...
We plan to use the 52840 to make a module with an external flash, if we apply the QSPI peripheral, must we use the P0.23,P1.00,P0.21,P0.25,P0.19 pins recommended in the specification...
